Applied Biosystems 7300 Installation And Maintenance Manual Download Page 144

Page: 144 / 174

Appendix A

Replacing the Halogen Lamp

118

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

Replacing the Halogen Lamp

PHYSICAL INJURY HAZARD.

The 7300/7500/7500 Fast

system and lamp are hot! The lamp can become very hot while in use. Allow sufficient

time for the lamp to cool, and put on protective, powder-free gloves before handling it.

PHYSICAL INJURY HAZARD.

Wear disposable, powder-free

gloves when handling the lamp to prevent burns and to prevent shortening the life of the

replacement lamp.

WARNING.

This instrument is designed for 12V, 75W halogen

lamps only.

Replace the halogen lamp after approximately 2000 hours of life.

Time Required

30 minutes

Materials

Required

Replacing the

Lamp

IMPORTANT!

Wear powder-free gloves when you handle the lamp.

Power off, then unplug the 7300/7500/7500 Fast system. Allow the instrument to
cool for 15 minutes.

Powder-free

gloves

Halogen bulb

(12V, 75W)

Safety

glasses

Screwdriver,

small

>00:15:00

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands