Applied Biosystems 7300 Installation And Maintenance Manual Download Page 54

Page: 54 / 174

Chapter 3

Installing the Software and Powering On the Instrument

Powering On the Instrument

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

Powering On the Instrument

IMPORTANT!

Do not power on the instrument unless you have installed the SDS software. If you power on the

instrument before you install the SDS software, the Windows operating system installs a generic driver for the

instrument, which does not allow the instrument to communicate with the SDS software.

IMPORTANT!

Make sure that the computer Hibernate power setting is disabled. If the Hibernate setting is enabled,

data collection stops when the computer goes into Hibernate mode. For more information, see

“Setting the Display

Settings and Power Options” on page 137

Powering On

Connect the Universal Serial Bus (USB) cable
between the:

• USB connector on the back left of the

instrument

and

• Either USB port on the computer

Tower Computer USB Connection

Laptop Computer USB Connection

USB

GR2374
7300/7500
electrical with laptop

USB

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands