Applied Biosystems 7300 Installation And Maintenance Manual Download Page 62

Page: 62 / 174

Chapter 4

Performing the Regions of Interest (ROI) Calibration

Overview

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

Overview

Note:

You can also use the Real-Time System Setup wizard to perform the procedure in

this chapter. To access the wizard, select

Program Files 7300/7500/7500

Fast System

Real-Time System Setup Wizard

Time Required

30 minutes

Materials

Required

When to Perform

the ROI

Calibration

Perform a regions of interest (ROI) calibration:

• When installing the system (you must perform all calibrations in this order: ROI

background optical (7500/7500 Fast systems only) pure dye instrument
verification).

• Every 6 months, or as often as necessary, depending on instrument use.
• After replacing the lamp.

IMPORTANT!

After every ROI calibration, you must perform a background calibration,

optical calibration (7500/7500 Fast systems only), pure dye calibration, and instrument

verification.

GR2170

Powder-free

Gloves

Safety

Goggles

ROI Calibration Plate

Centrifuge with plate

adapter

Applied Biosystems

Real-Time PCR System

Spectral Calibration Kit

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands