Applied Biosystems 7300 Installation And Maintenance Manual Download Page 168

Page: 168 / 174

142

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Index

defragmenting the hard drive

114

diagram, installation workflow

disk cleanup

114

disk space, checking

107

display settings, setting

137

documentation, related

xii

documentation, shipped with the instrument

drivers, automatically installed

electrical protective devices

electrical safety

xxiii

electromagnetic compatibility standards.

See

EMC

standards

EMC standards

xxv

encryption software

ergonomics, safety

xxv

error status light, troubleshooting

FAM

™

pure dye

Fast plate

description

do not vortex

location of notched corner

Fast system, spectra data for pure dyes

Fast versus standard plates

file compression software

firewall software

flow diagram, installation

front panel indicators

location

troubleshooting

Function test

performing

troubleshooting

fuses, changing

122

guidelines

chemical safety

xxii

chemical waste disposal

xxii

chemical waste safety

xxii

halogen bulb

replacing

117

warning, hot

118

119

hardware, selecting additional

hazard icons.

See

safety symbols, on instruments

hazard symbols.

See

safety symbols, on instruments

hazards.

See

safety

heated cover assembly

IMPORTANT, description

xvi

indicator lights

location

troubleshooting

Information Development department, contacting

xii

Installation and Maintenance Guide overview

installation category

xxiv

installation kit, TaqMan

RNase P Chemistry

installing

before starting

materials shipped

planning

preparing the site

SDS software

SDS software, administrator rights required

selecting the method

third-party software

times required

using the Installation and Maintenance Guide

using the wizard

Windows service pack updates

124

instrument

indicator lights

layout

moving

115

opening door

powering on

preparing the site

setting up

shutting down

101

uncrating

unpacking

instrument function test, performing

instrument operation, safety

JOE

™

pure dye

kits provided

packing

software and documentation

Spectral Calibration

TaqMan Reagent Starter

TaqMan

Reagent Starter

TaqMan

RNase P Chemistry

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Brands by name

Popular brands