Applied Biosystems 7300 Installation And Maintenance Manual Download Page 51

Page: 51 / 174

Chapter 3

Installing the Software and Powering On the Instrument

Installing the SDS Software for the 7300/7500/7500 Fast System

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

Installing the SDS Software for the 7300/7500/7500 Fast
System

IMPORTANT!

You must be logged in with Windows administrator privileges to install

the SDS Software.

Obtain the Software CD and Documentation CD from the Software and
Documentation kit.

Power on the computer, then log in as a Windows operating system administrator,
as described in the

Applied Biosystems Real-Time PCR System Computer Setup

Guide

Insert the SDS Software CD into the CD drive of the computer. The Real-Time
System Setup wizard starts automatically after a short delay.
If the wizard does not automatically start, double-click

(

My Computer

navigate to the CD drive, then double-click

SystemSetupWizard.exe

Click

Install the SDS Software

In the Software Installation Materials Required page, select the

I have obtained the

materials listed above check

box, then click

Click

Summary of Contents for 7300















































































































































































Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands

Applied Biosystems 7300, Installation And Maintenance Manual

Search results

Summary of Contents for 7300

Reviews:

Related manuals for 7300

Brands by name

Popular brands