Amada MM-L300A Original Instructions Manual Download Page 71

Page: 71 / 180

MM-L300A

6. How to Operate the PC Software

6-30

3) Set the upper/lower limit judgment value, and then set the position from

Average, Range, or ±3

in the unit of %. (1%

≒

graph intensity scale ×

1/100)



If the setting range conditions above is not satisfied, a message appears when a

condition is changed or added.

Click the [OK] button to return.

4) Click the [Set Condition] button to determine the setting.

Also, when the [Set Condition] button is clicked, the Detail Condition Window is
displayed and setting contents can be checked. The Detail Condition Window can also
be displayed by clicking the [Detail Display] button.

Upper/lower limit

judgment

value of this section is
changed to specified value.

Summary of Contents for MM-L300A





















































































































































































Search results

Summary of Contents for MM-L300A

Reviews:

Brands by name

Popular brands

Amada MM-L300A, Original Instructions Manual

Search results

Summary of Contents for MM-L300A

Reviews:

Brands by name

Popular brands