manualshive.com logo in svg

Amada MM-L300A, Original Instructions Manual

Share
Download
Amada MM-L300A Original Instructions Manual Download Page 148

MM-L300A 

11. EtherNet/IP 

11-3 

5)  Insert the ANYBUS connector where the ANYBUS slot cover was present 

and lock the ANYBUS connector by tightening two screws with the L-type 
wrench attached to the ANYBUS connector. 

       

 

 

6)  Turn ON the 

MM-L300A

. 

Confirm that the Module Status (MS) LED flashes in green after a while and 
the connector becomes in an idle state. 
If the LED does not light up normally, perform Step 5. It may a contact failure 
of the connector. 

       

 

 

Cable connection with the 

MM-L300A

 

Install the EtherNet port to connect to a network by EtherNet/IP (option). Connect the 
LAN cable (option) to the EtherNet port. For how to use EtherNet/IP, consult us. 

* 

The LAN connector does not support EtherNet/IP. 

 

 

Summary of Contents for MM-L300A





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands