Amada MM-L300A Original Instructions Manual Download Page 68

Page: 68 / 180

MM-L300A

6. How to Operate the PC Software

6-27

(5) Calculation of the selected waveform data

Select the waveform data and click the [Calculate] button.

The Condition Configuration Window is displayed automatically. The condition of
average is selected by default. According to the use, Average, Range or ±3

can be

selected from the combo box.

Average

- Upper limit judgment value: data average value
- Lower limit judgment value: data average value

Range

Upper limit
judgment value

Lower limit
judgment value

Upper limit judgment value
(Max. value of the selected waveform)

Reference waveform
(Data average value)

Lower limit judgment value
(Min. value of the selected waveform)

Reference waveform
(Data average value)

Summary of Contents for MM-L300A





















































































































































































Search results

Summary of Contents for MM-L300A

Reviews:

Brands by name

Popular brands

Amada MM-L300A, Original Instructions Manual

Search results

Summary of Contents for MM-L300A

Reviews:

Brands by name

Popular brands