Altera UG-01080 Page 320 User Manual Download

Page: 320 / 702

Parameter

Range

Description

RX word aligner mode

bit_slip

sync_sm

manual

Specifies one of the following 3 modes for the

word aligner:
• Bit_slip : You can use bit slip mode to

shift the word boundary. For every rising

edge of the

rx_bitslip signal

, the word

boundary is shifted by 1 bit. Each bit

slip

removes the earliest received bit from the

received data

• Sync_sm : In synchronous state machine

mode, a programmable state machine

controls word alignment. You can only use

this mode with 8B/10B encoding. The data

width at the word aligner can be 10 or 20

bits. When you select this word aligner

mode, the synchronous state machine has

hysteresis that is compatible with XAUI.

However, when you select cpri for the

Standard PCS Protocol Mode, this option

selects the deterministic latency word

aligner mode.

• Manual : This mode Enables word

alignment by asserting the

rx_std_wa_

patternalign

. This is an edge sensitive

signal.

RX word aligner pattern length

7, 8, 10

16, 20, 32

Specifies the length of the pattern the word

aligner uses for alignment.

RX word aligner pattern (hex)

User-specified Specifies the word aligner pattern in hex.

Number of word alignment patterns to

achieve sync

1-256

Specifies the number of valid word alignment

patterns that must be received before the

word aligner achieves synchronization lock.

The default is 3.

Number of invalid words to lose sync

1-256

Specifies the number of invalid data codes or

disparity errors that must be received before

the word aligner loses synchronization. The

default is 3.

Number of valid data words to

decrement error count

1-256

Specifies the number of valid data codes that

must be received to decrement the error

counter. If the word aligner receives enough

valid data codes to decrement the error count

to 0, the word aligner returns to synchroniza‐

tion lock.

Run length detector word count

0-63

Specifies the maximum number of contiguous

0s or 1s in the data stream before the word

aligner reports a run length violation.

12-22

Standard PCS Parameters for the Native PHY

UG-01080

2015.01.19

Altera Corporation

Stratix V Transceiver Native PHY IP Core

Send Feedback

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for UG-01080

Reviews:

Related manuals for UG-01080

Brands by name

Popular brands

Altera UG-01080, User Manual

Search results

Summary of Contents for UG-01080

Reviews:

Related manuals for UG-01080

Brands by name

Popular brands