manualshive.com logo in svg

Altera UG-01080, User Manual, Page: 41 / 702

Share
Download
Altera UG-01080 User Manual Download Page 41

Signal Name

XGMII Signal Name

Description

xgmii_tx_dc_[44]

xgmii_sdr_ctrl[4]

Lane 4 control

xgmii_tx_dc_[52:45]

xgmii_sdr_data[47:40]

Lane 5 data

xgmii_tx_dc_[53]

xgmii_sdr_ctrl[5]

Lane 5 control

xgmii_tx_dc_[61:54]

xgmii_sdr_data[55:48]

Lane 6 data

xgmii_tx_dc_[62]

xgmii_sdr_ctrl[6]

Lane 6 control

xgmii_tx_dc_[70:63]

xgmii_sdr_data[63:56]

Lane 7 data

xgmii_tx_dc_[71]

xgmii_sdr_ctrl[7]

Lane 7 control

Table 3-12: Mapping from XGMII RX Bus to the XGMII SDR Bus

Signal Name

XGMII Signal Name

Description

xgmii_rx_dc_[7:0]

xgmii_sdr_data[7:0]

Lane 0 data

xgmii_rx_dc_[8]

xgmii_sdr_ctrl[0]

Lane 0 control

xgmii_rx_dc_[16:9]

xgmii_sdr_data[15:8]

Lane 1 data

xgmii_rx_dc_[17]

xgmii_sdr_ctrl[1]

Lane 1 control

xgmii_rx_dc_[25:18]

xgmii_sdr_data[23:16]

Lane 2 data

xgmii_rx_dc_[26]

xgmii_sdr_ctrl[2]

Lane 2 control

xgmii_rx_dc_[34:27]

xgmii_sdr_data[31:24]

Lane 3 data

xgmii_rx_dc_[35]

xgmii_sdr_ctrl[3]

Lane 3 control

xgmii_rx_dc_[43:36]

xgmii_sdr_data[39:32]

Lane 4 data

xgmii_rx_dc_[44]

xgmii_sdr_ctrl[4]

Lane 4 control

xgmii_rx_dc_[52:45]

xgmii_sdr_data[47:40]

Lane 5 data

xgmii_rx_dc_[53]

xgmii_sdr_ctrl[5]

Lane 5 control

xgmii_rx_dc_[61:54]

xgmii_sdr_data[55:48]

Lane 6 data

xgmii_rx_dc_[62]

xgmii_sdr_ctrl[6]

Lane 6 control

xgmii_rx_dc_[70:63]

xgmii_sdr_data[63:56]

Lane 7 data

xgmii_rx_dc_[71]

xgmii_sdr_ctrl[7]

Lane 7 control

10GBASE-R PHY Status, 1588, and PLL Reference Clock Interfaces

This section describes the 10GBASE-R PHY status, 1588, and PLL reference clock interfaces.

UG-01080

2015.01.19

10GBASE-R PHY Status, 1588, and PLL Reference Clock Interfaces

3-17

10GBASE-R PHY IP Core

Altera Corporation

Send Feedback

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments