manualshive.com logo in svg

Altera UG-01080, User Manual, Page: 376 / 702

Share
Download
Altera UG-01080 User Manual Download Page 376

Arria V Transceiver Native PHY IP Core

13

2015.01.19

UG-01080

Subscribe

Send Feedback

The Arria V Transceiver Native PHY IP Core provides direct access to all control and status signals of the

transceiver channels. Unlike other PHY IP Cores, the Native PHY IP Core does not include an Avalon

Memory-Mapped (Avalon-MM) interface. Instead, it exposes all signals directly as ports. The Arria V

Transceiver Native PHY IP Core provides the following datapaths:
• Standard PCS—When you enable the Standard PCS, you can select the PCS functions and control and

status ports that your transceiver PHY requires.

• PMA Direct—When you select PMA Direct mode, the Native PHY provides direct access to the PMA

from the FPGA fabric; consequently, the latency for transmitted and received data is lower. However,

you must implement any PCS function that your design requires in the FPGA fabric. PMA Direct

mode is supported for Arria V GT, ST, and GZ devices only.

The Native Transceiver PHY does not include an embedded reset controller. You can either design

custom reset logic or incorporate Altera’s “Transceiver PHY Reset Controller IP Core” to implement reset

functionality. The Native Transceiver PHY’s primary use in Arria V GT devices is for data rates greater

than 6.5536 Gbps.
As the following figure  illustrates, TX PLL and clock data recovery (CDR) reference clocks from the pins

of the device are input to the PLL module and CDR logic. When enabled, the Standard PCS drives TX

parallel data and receives RX parallel data. In PMA Direct mode, the PMA serializes TX data it receives

from the fabric and drives RX data to the fabric.

©

 2015 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are

trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as

trademarks or service marks are the property of their respective holders as described at

 www.altera.com/common/legal.html

. Altera warrants performance

of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any

products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information,

product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device

specifications before relying on any published information and before placing orders for products or services.

ISO

9001:2008

Registered

www.altera.com

101 Innovation Drive, San Jose, CA 95134

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments