Altera UG-01080 Page 68 User Manual Download

Page: 68 / 702

• An embedded processor mode to override the state

machine

based training algorithm. This mode

allows an embedded processor to establish link data rates instead of establishing the link using the

state

machine

based training algorithm.

The following figure illustrates the link training process, where the link partners exchange equalization

data.

Figure 4-3: TX Equalization for Link Partners

Encode

Handshake

Adapt

Decode

Encode

Handshake

Adapt

Decode

Calculate

BER

Send Eq

Change Eq

Ack Change

Data Transmission

Adaptation Feedback

TX equalization includes the following steps which are identified in this figure.
1. The receiving link partner calculates the BER.

2. The receiving link partner transmits an update to the transmitting link partner TX equalization

parameters to optimize the TX equalization settings

3. The transmitting partner updates its TX equalization settings.

4. The transmitting partner acknowledges the change.
This process is performed first for the V

, then the pre-emphasis, the first post

tap, and then pre-

emphasis pre-tap.
The optional backplane daisy-chain topology can replace the spoke or hub switch topology. The following

illustration highlights the steps required for TX Equalization for Daisy Chain Mode.

4-12

10GBASE-KR PHY IP Core Functional Description

UG-01080

2015.01.19

Altera Corporation

Backplane Ethernet 10GBASE-KR PHY IP Core with Early Access FEC Option

Send Feedback

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for UG-01080

Reviews:

Related manuals for UG-01080

Brands by name

Popular brands

Altera UG-01080, User Manual

Search results

Summary of Contents for UG-01080

Reviews:

Related manuals for UG-01080

Brands by name

Popular brands