manualshive.com logo in svg

Altera UG-01080, User Manual, Page: 125 / 702

Share
Download
Altera UG-01080 User Manual Download Page 125

Addr

Bit

R/W

Name

Description

0xB1

0

RO

SEQ Link Ready

When asserted, the sequencer is indicating that

the link is ready.

Related Information

Avalon Interface Specifications

PMA Registers

The PMA registers allow you to reset the PMA and provide status information.

Table 5-14: PMA Registers - Reset and Status

The following PMA registers allow you to reset the PMA and provide status information.

Addr

Bit

Access

Name

Description

0x22

0

RO

pma_tx_pll_is_

locked

Indicates that the TX PLL is locked to the input

reference clock.

0x44

1

RW

reset_tx_

digital

Writing a 1 causes the internal TX digital reset signal

to be asserted. You must write a 0 to clear the reset

condition.

2

RW

reset_rx_analog

Writing a 1 causes the internal RX analog reset signal

to be asserted. You must write a 0 to clear the reset

condition.

3

RW

reset_rx_

digital

Writing a 1 causes the internal RX digital reset signal

to be asserted. You must write a 0 to clear the reset

condition.

0x61

[31:0]

RW

phy_serial_

loopback

Writing a 1 puts the channel in serial loopback mode.

0x64

[31:0]

RW

pma_rx_set_

locktodata

When set, programs the RX CDR PLL to lock to the

incoming data.

0x65

[31:0]

RW

pma_rx_set_

locktoref

When set, programs the RX clock data recovery

(CDR) PLL to lock to the reference clock.

0x66

[31:0]

RO

pma_rx_is_

lockedtodata

When asserted, indicates that the RX CDR PLL is

locked to the RX data, and that the RX CDR has

changed from LTR to LTD mode.

0x67

[31:0]

RO

pma_rx_is_

lockedtoref

When asserted, indicates that the RX CDR PLL is

locked to the reference clock.

5-16

PMA Registers

UG-01080

2015.01.19

Altera Corporation

1G/10 Gbps Ethernet PHY IP Core

Send Feedback

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments