Altera UG-01080 Page 210 User Manual Download | Manualshive

Page: 210 / 702

background image

“

Section 4.2.3 Link Equalization Procedure for 8.0 GT/s Data Rate

” in the

PCI Express Base Specification,

Rev. 3.0

provides detailed information about the four-stage link equalization procedure. A new LTSSM

state, Recovery.Equalization with Phases 0–3, reflects progress through Gen3 equalization. Phases 2 and 3

of link equalization are optional; however, the link must progress through all four phases, even if no

adjustments occur. Skipping Phases 2 and 3 speeds up link training at the expense of link BER optimiza‐

tion.

Related Information

PHY Interface for the PCI Express Architecture PCI Express 3.0

Phase 0

Phase 0 includes the following steps:
1. Upstream component enters Phase 0 of equalization during Recovery.Rcvrconfig by sending EQ TS2

training sets with starting presets for the downstream component. EQ TS2 training sets may be sent at

2.5 GT/s or 5 GT/s.

2. The downstream component enters Phase 0 of equalization after exiting Recovery.Speed at 8 GT/s. It

receives the starting presets from the training sequences and applies them to its transmitter. At this

time, upstream component has entered Phase 1 and is operating at 8 GT/s.

3. To move to Phase 1, the receiver must have a BER < 10

-4

and should be able to decode enough

consecutive training sequences.

4. The downstream component must detect training sets with Equalization Control (EC) bits set to 2’b01

in order to move to EQ Phase 1.

Phase 1

During Phase 1 of equalization process, the link partners exchange FS (Full Swing) and LF (Low

Frequency) information. These values represent the upper and lower bounds for the TX coefficients. The

receiver uses this information to calculate and request the next set of transmitter coefficients.
1. Once training sets with EC bits set to 1’b0 are captured on all lanes, the upstream component moves to

EQ Phase 2 sending EC=2’b10 along with starting pre-cursor, main cursor, and post-cursor

coefficients.

2. The downstream component detects these new training sets, and moves to EQ Phase 2.

Phase 2 (Optional)

This section describes the (optional) Phase 2.
During Phase 2, the Endpoint tunes the TX coefficients of the Root Port. The TS1 Use Preset bit

determines whether the Endpoint uses presets for coarse resolution or coefficients for fine resolution.
Note: If you are using the PHY IP Core for PCI Express (PIPE) PCI Express as an Endpoint, you cannot

perform Phase 2 tuning. The PIPE interface does not provide any measurement metric to the Root

Port to guide coefficient preset decision making. The Root Port should reflect the existing

coefficients and move to the next phase. The default Full Swing (FS) value advertized by Altera

device is 40 and Low Frequency (LF) is 13.

If you are using the PHY IP Core for PCI Express (PIPE) PCI Express as Root Port, the End Point can

tune the Root Port TX coefficients.

8-22

Phase 0

UG-01080

2015.01.19

Altera Corporation

PHY IP Core for PCI Express (PIPE)

Send Feedback

«
...
208
209
210
211
212
...
»

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for UG-01080

Brand: Haier Pages: 160

Brand: R&S Pages: 220

Brand: Garmin Pages: 44

Brand: Hanwha Techwin Pages: 2

Brand: Hanwha Techwin Pages: 2

Brand: Icom Pages: 3

Multimedia Master Remote

Brand: Remotec Pages: 19

Brand: Onkyo Pages: 144

Brand: TechniSat Pages: 4

MAGNETIC Deluxe 1Rw

Brand: YOODA Pages: 2

Brand: Maico Pages: 24

AIR-EAGLE XLT 44P-8-ESTOP

Brand: BWI Eagle Pages: 3

Brand: HomeFree Systems Pages: 7

THERMOPOINT TM/J-500

Brand: NIVELCO Pages: 28

Brand: Grandbeing Pages: 25

Brand: Harman Kardon Pages: 52

Brand: Denon Professional Pages: 16

Brand: Deif Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands