manualshive.com logo in svg

Altera UG-01080, User Manual, Page: 488 / 702

Share
Download
Altera UG-01080 User Manual Download Page 488

Table 15-3: PMA Options  

Parameter

Range

Description

Data rate

Device

Dependent

Specifies the data rate. The maximum data rate is

12.5 Gbps.

TX local clock division factor

1, 2, 4, 8

Specifies the value of the divider available in the

transceiver channels to divide the input clock to

generate the correct frequencies for the parallel

and serial clocks. This divisor divides the fast

clock from the PLL in nonbonded configurations.

PLL base data rate

Device

Dependent

Shows the base data rate of the clock input to the

TX PLL.The PLL base data rate is computed

from the TX local clock division factor

multiplied by the data rate.
Select a PLL base data rate that minimizes the

number of PLLs required to generate all the

clocks for data transmission. By selecting an

appropriate PLL base data rate, you can change

data rates by changing the TX local clock

division factor used by the clock generation

block.

Related Information

•

Transceiver Architecture in Cyclone V Devices

•

Device Datasheet for Cyclone V Devices

TX PMA Parameters

Note: For more information about PLLs in Cyclone V devices, refer to the 

Cyclone V PLLs

 section in

Clock Networks and PLLs in Cyclone V Devices.

Table 15-4: TX PMA Parameters

Parameter

Range

Description

Enable TX PLL dynamic reconfi‐

guration

On/Off

When you turn this option On, you can

dynamically reconfigure the PLL. This option is

also required to simulate TX PLL reconfiguration.

If you turn this option On, the Quartus II Fitter

prevents PLL merging by default; however, you

can specify merging using the 

XCVR_TX_PLL_

RECONFIG_GROUP

 QSF assignment.

UG-01080

2015.01.19

TX PMA Parameters

15-5

Cyclone V Transceiver Native PHY IP Core Overview

Altera Corporation

Send Feedback

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments