manualshive.com logo in svg

Altera UG-01080, User Manual, Page: 52 / 702

Share
Download
Altera UG-01080 User Manual Download Page 52

Word Addr

Bit

R/W

Name

Description

0x083

[5:0]

R

BER_COUNT[5:0]

For Stratix IV devices only, records

the bit error rate (BER). From block:

BER monitor

[13:6]

R

ERROR_BLOCK_COUNT[7:0]

For Stratix IV devices only, records

the number of blocks that contain

errors. From Block: Block synchron‐

izer

[14]

R

LATCHED_HI_BER

Latched version of 

HI_BER 

. From

block: BER monitor

[15]

R

LATCHED_BLOCK_LOCK

Latched version of 

BLOCK_LOCK

. From

Block: Block synchronizer

Related Information

•

Loopback Modes

 on page 16-58

•

Avalon Interface Specifications

10GBASE-R PHY Dynamic Reconfiguration for Stratix IV Devices

The 10GBASE-R PHY includes additional top-level signals when configured with an external modules for

PMA control and dynamic reconfiguration.
You enable this configuration by turning on Use external PMA control and reconfig available for Stratix

IV GT devices.

Table 3-17: External PMA and Reconfiguration Signals

Signal Name

Direction

Description

gxb_pdn

Input

When asserted, powers down the entire GT block.

Active high. For Stratix IV de

pll_pdn

Input

When asserted, powers down the TX PLL. Active high.

cal_blk_pdn

Input

When asserted, powers down the calibration block.

Active high.

cal_blk_clk

Input

Calibration clock. For Stratix IV devices only. It must

be in the range 37.5-50 MHz. You can use the same

clock for the 

phy_mgmt_clk

 and the 

cal_blk_clk

.

pll_locked

Output

When asserted, indicates that the TX PLL is locked.

reconfig_to_xcvr[3:0]

Input

Reconfiguration signals from the Transceiver Reconfi‐

guration Controller to the PHY device. This signal is

only available in Stratix IV devices.

3-28

10GBASE-R PHY Dynamic Reconfiguration for Stratix IV Devices

UG-01080

2015.01.19

Altera Corporation

10GBASE-R PHY IP Core

Send Feedback

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments