manualshive.com logo in svg

Altera UG-01080, User Manual, Page: 65 / 702

Share
Download
Altera UG-01080 User Manual Download Page 65

Parameter Name

Options

Description

Enable FEC status ports

On/Off

When you turn this option the core includes the

rx_block_lock

, 

rx_parity_good

, 

rx_parity_

invalid

, and 

tx_frame

 signals.

Note: This parameter is not implemented in

the early access release.

Related Information

Analog Parameters Set Using QSF Assignments

 on page 19-1

1GbE Parameters

The 1GbE parameters allow you to specify options for the 1GbE mode.

Table 4-8: 1Gb Ethernet Parameters

Parameter Name

Options

Description

Enable 1Gb Ethernet protocol

On/Off

When you turn this option On, the core includes

the GMII interface and related logic.

Enable SGMII bridge logic

On/Off

When you turn this option On, the core includes

the SGMII clock and rate adaptation logic for

the PCS. You must turn this option On if you

enable 1G mode.

Enable IEEE 1588 Precision Time

Protocol

On/Off

When you turn this option On, the core includes

a module in the PCS to implement the IEEE

1588 Precision Time Protocol.

PHY ID (32 bit)

32-bit value

An optional 32-bit value that serves as a unique

identifier for a particular type of PCS. The

identifier includes the following components:
• Bits 3-24 of the Organizationally Unique

Identifier (OUI) assigned by the IEEE

• 6

-

bit model number

• 4-bit revision number
If unused, do not change the default value which

is 0x00000000.

PHY Core version (16 bits)

16-bit value

This is an optional 16

-

bit value identifies the

PHY core version.

Reference clock frequency

125.00 MHz 
62.50 MHz

Specifies the clock frequency for the

1GBASE

-

KR PHY IP Core. The default is 125

MHz.

Related Information

1588 Delay Requirements

 on page 3-30

UG-01080

2015.01.19

1GbE Parameters

4-9

Backplane Ethernet 10GBASE-KR PHY IP Core with Early Access FEC Option

Altera Corporation

Send Feedback

Summary of Contents for UG-01080































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments