Agilent Technologies InfiniiVision 4000 X-Series, Programmer'S Manual

Page: 1349 / 1352

Index
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide 1349
title channels , 271
title, mask test , 540
token PID, USB search , 905
token PID, USB trigger , 813
tolerance, automask , 516 , 517
top of waveform value measured , 480
total frame count (CAN) , 673
total frame count (FlexRay) , 693
total harmonics distortion (THD) , 564
total waveforms in mask test , 521
touchscreen on/off , 922
trace memory , 223
track measurements , 457
tracking, dual channel waveform
generator , 1090
trademarks , 2
transfer instrument state , 171 , 919
transforms, math , 358
transient response , 505
transient response analysis , 608 , 609 , 612
TRANsition SEARch commands , 837
transition search qualifier , 838
transition search slope , 839
transition search time , 841
transition trigger qualifier , 998
transition trigger slope , 999
transition trigger source , 840 , 1000
transition trigger time , 1001
transmit word size, I2S , 721
tree traversal rules , 1213
trend measurement , 367
TRG (Trigger) , 181 , 183 , 184
TRIG OUT BNC , 257
trigger armed event register , 211 , 213
trigger burst, UART , 786
trigger channel source , 974 , 1006
TRIGger commands , 935
TRIGger commands, general , 937
trigger data, UART , 787
TRIGger DELay commands , 947
trigger duration , 981 , 982
TRIGger EBURst commands , 954
TRIGger EDGE commands , 959
trigger edge coupling , 961
trigger edge slope , 964
trigger edge slope, Edge Then Edge
trigger , 952
trigger edge source, Edge Then Edge
trigger , 953
trigger event bit , 225
Trigger Event Register (TER) , 1182
TRIGger FLEXray commands , 685
TRIGger GLITch commands , 966
trigger holdoff , 940
trigger idle, UART , 788
TRIGger IIC commands , 723
trigger level auto set up , 941
trigger level constants , 273
trigger level voltage , 962
trigger level, high , 942
trigger level, low , 943
TRIGger LIN commands , 733
TRIGger M1553 commands , 747
trigger occurred , 183
TRIGger OR commands , 975
TRIGger PATTern commands , 977
trigger pattern qualifier , 983
trigger qualifier, UART , 789
trigger reset conditions , 177 , 916
TRIGger RUNT commands , 986
TRIGger SHOLd commands , 991
trigger SPI clock slope , 757
TRIGger SPI commands , 754
trigger status bit , 225
trigger sweep mode , 935
TRIGger TV commands , 997 , 1002
trigger type, ARINC 429 , 666 , 844
trigger type, SPI , 768
trigger type, UART , 790
TRIGger UART commands , 770
TRIGger USB commands , 792
TRIGger ZONE commands , 1012
trigger, ARINC 429 source , 659
trigger, CAN , 679
trigger, CAN pattern data length , 682
trigger, CAN pattern ID mode , 684
trigger, CAN sample point , 675
trigger, CAN signal baudrate , 676
trigger, CAN signal definition , 677
trigger, CAN source , 678
trigger, duration greater than , 981
trigger, duration less than , 982
trigger, duration range , 985
trigger, edge coupling , 961
trigger, edge level , 962
trigger, edge reject , 963
trigger, edge slope , 964
trigger, edge source , 965
trigger, FLEXray , 695
trigger, FLEXray error , 696
trigger, FLEXray event , 699
trigger, force a , 938
trigger, glitch greater than , 968
trigger, glitch less than , 969
trigger, glitch level , 970
trigger, glitch polarity , 971
trigger, glitch qualifier , 972
trigger, glitch range , 973
trigger, glitch source , 974
trigger, high frequency reject filter , 939
trigger, holdoff , 940
trigger, I2S , 713
trigger, I2S alignment , 706
trigger, I2S audio channel , 715
trigger, I2S clock slope , 708
trigger, I2S CLOCksource , 710
trigger, I2S DATA source , 711
trigger, I2S pattern data , 716
trigger, I2S pattern format , 718
trigger, I2S range , 719
trigger, I2S receiver width , 709
trigger, I2S transmit word size , 721
trigger, I2S word select (WS) low , 722
trigger, I2S word select (WS) source , 712
trigger, IIC clock source , 725
trigger, IIC data source , 726
trigger, IIC pattern address , 727
trigger, IIC pattern data , 728
trigger, IIC pattern data 2 , 729
trigger, IIC qualifier , 730
trigger, IIC signal baudrate , 737
trigger, IIC type , 731
trigger, LIN , 741
trigger, LIN pattern data , 743
trigger, LIN pattern data length , 745
trigger, LIN pattern format , 746
trigger, LIN sample point , 736
trigger, LIN signal definition , 1161
trigger, LIN source , 738
trigger, mode , 944
trigger, noise reject filter , 945
trigger, Nth edge burst source , 958
trigger, Nth edge in burst slope , 957
trigger, Nth edge of burst count , 955
trigger, Nth edge of Edge Then Edge
trigger , 951
trigger, SPI clock slope , 757
trigger, SPI clock source , 760
trigger, SPI clock timeout , 758
trigger, SPI frame source , 761
trigger, SPI framing , 759
trigger, SPI pattern MISO width , 765
trigger, SPI pattern MOSI width , 767
trigger, sweep , 946
trigger, threshold , 1165
trigger, TV line , 1003
trigger, TV mode , 1004 , 1166
trigger, TV polarity , 1005
trigger, TV source , 1006
trigger, TV standard , 1007
trigger, UART base , 785
trigger, UART baudrate , 774
trigger, UART bit order , 775
trigger, UART parity , 781
trigger, UART polarity , 782
trigger, UART Rx source , 783
trigger, UART Tx source , 784
trigger, UART width , 791
trigger, USB , 800
truncation rules , 1210
TST (Self Test) , 185
tstart , 1142
tstop , 1143
TTL threshold voltage for digital channels , 307 ,
1118
TTL trigger threshold voltage , 1165
turn function on or off , 1130
turn off channel , 198
turn off channel labels , 317
turn off digital pod , 198
turn off math function , 198
turn off time , 497 , 574
turn on channel labels , 317
turn on channel number display , 1123
turn on time , 498 , 574