Agilent Technologies InfiniiVision 4000 X-Series Programmer'S Manual Download Page 1209 | Manualshive

Page: 1209 / 1352

background image

More About Oscilloscope Commands

40

Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide

1209

Valid Command/Query Strings

•

"Program Message Syntax"

on page 1209

•

"Duplicate Mnemonics"

on page 1213

•

"Tree Traversal Rules and Multiple Commands"

on page 1213

Program Message Syntax

To program the instrument remotely, you must understand the command
format and structure expected by the instrument. The IEEE 488.2 syntax
rules govern how individual elements such as headers, separators, program
data, and terminators may be grouped together to form complete
instructions. Syntax definitions are also given to show how query
responses are formatted. The following figure shows the main syntactical
parts of a typical program statement.

Instructions (both commands and queries) normally appear as a string
embedded in a statement of your host language, such as Visual Basic or
C/C++. The only time a parameter is not meant to be expressed as a string
is when the instruction's syntax definition specifies <block data>, such as
<learn string>. There are only a few instructions that use block data.

Program messages can have long or short form commands (and data in
some cases — see

"Long Form to Short Form Truncation Rules"

on

page 1210), and upper and/or lower case ASCII characters may be used.
(Query responses, however, are always returned in upper case.)

Instructions are composed of two main parts:

•

The header, which specifies the command or query to be sent.

•

The program data, which provide additional information needed to
clarify the meaning of the instruction.

Instruction

Header

The instruction header is one or more mnemonics separated by colons (:)
that represent the operation to be performed by the instrument.

":DISPlay:LABel ON" is a command. Queries are indicated by adding a
question mark (?) to the end of the header, for example, ":DISPlay:LABel?".
Many instructions can be used as either commands or queries, depending

":DISPLAY:LABEL ON"

3URJUDP0HVVDJH

,QVWHDGHU

6HSDUDWRU

3URJUDP'DWD

«
...
1207
1208
1209
1210
1211
...
»

Summary of Contents for InfiniiVision 4000 X-Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for InfiniiVision 4000 X-Series

Brand: Backyard Discovery Pages: 51

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

Brand: Jaga Pages: 32

Brand: Madsen Pages: 206

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

Brand: Yamaha Pages: 48

Carestation 620

Brand: GE Pages: 268

Brand: GE Pages: 50

Brand: Numark Pages: 11

ResQCRP ResQPUMP ACD-CPR

Brand: Advanced Circulatory Pages: 2

Big Wheel RN1 Series

Brand: Osborne Pages: 8

Brand: Gomaco Pages: 30

Brand: Panduit Pages: 4

home FLP 1600 SOLAR

Brand: Somogyi Elektronic Pages: 15

Brand: TEUCER Pages: 4

Brand: T&R Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands