Zener SMARTSTART 6000, Инструкция по эксплуатации

Страница: 41 / 57

Specification
Technical Manual: Smartstart
®
6000 IMI0042 rev K
Page 38
Input Voltage:
6R series: 220 to 460Vac
6R15 ‐ 80: 380Vac to 415Vac
6V series: 600 to 1000V (+10%)
Input Frequency: 50 / 60Hz +/ ‐ 3Hz,
Auto detecting
Control Supply: 24Vdc (+15%, ‐ 15%)
24VDC Power Supply (min. requirements):
Power Supply O/P: 24VDC Regulated
Peak power requirements:
6R15 ‐ 30: 1.5 Amps (36W)
6R60 ‐ 80: 2 Amps (48W)
6R100–220/6V90: 3.0Amps (72W)
6R300–880: 4.0 Amps (96W)
6V200 ‐ 400: 4.0 Amps (96W)
These ratings allow for peak current requirements of internal
fans
AC Control Supply Options Available:
240VAC: All Models
18VAC: All Models
415VAC Self Powered 6R15/30/60/80 Only
Configurations: i) 3 wire & 6 wire
ii) Bypass or Continuous
6R15 to 6R80 have integral Bypass
Contactor.
Duty :
Light Duty: 300% for 15 secs; 10start/hr
350% for 10secs; 10start/hr
Standard Duty: 300% for 30secs; 10start/hr
400% for 10 secs; 10start/hr
Severe Duty: 450 for 20 secs; 5start/hr
300% for 60 secs; 5start/hr
SCR PIV: Minimum 1400V (6R series)
Minimum 3600V (6V series)
SCR configuration: Full ‐ wave
Dv/dt suppression: RC snubber networks
Over Voltage: MOV
Rated Insulation: 2Kv (6R series)
EMC Class A (to AS61800 – C ‐ tick)
Current Feedback Current transformer in circuit at all
times.
Torque controlled Ramp or voltage
ramp, with current limit override
Standards Compliance AS31800 C ‐ tick; AS3947.4.2, IEC60947 ‐
4 ‐ 2
Environment:
Enclosure protection: IP00 – IP20
Operating Temp. 0 to 55°C (derate by 1% / °C >40°C)
Cooling: Temperature controlled forced
ventilated
Maximum Altitude: 1000m without derating
Operating position: Vertical
Pollution: Degree 3 conforming to IEC947 ‐ 4 ‐ 2
Inputs:
Digital Inputs : 24Vdc Logic
Function: 2x Programmable inputs
1x Enable Input
Thermistor: Thermistor or NC switch
PTC type, Trip Resistance 3000Ohms,
<20ohms detected as Short Circuit.
Outputs:
Digital Output: 4 Programmable Relays
Contact Rating: 5A 250Vac; 5A 30VDC resistive
Analogue Output: 1x Programmable Output
Signal: 0 ‐ 10V, 0 ‐ 5V, 4 ‐ 20mA
Communications: Modbus RS485 (Standard)
Ethernet (Modbus) Option
Protection:
Motor Overload Adjustable; Class 10, 10A, 20, 25, 30 type R1,
total memory function
SCR Over temp. Heat sink temperature
SCR protection: Current & thermal modelling
Under Current Adjustable level and trip time
Over Current Adjustable level and trip time
Under Torque: Adjustable level and trip time
Over Torque: Adjustable level and trip time
Motor Stalled 300% for 3 seconds (run mode only)
Current limit Adjustable
Starter Overload Current & thermal modelling
O/P Short Circuit Semiconductor fuses (optional)
Voltage imbalance Input voltage imbalance
Current Imbalance Input & output current imbalance
Bypass failure No bypass after ramp time or during run
mode
SCR fault Open or Short circuit SCR
Acc over time Accel time exceeds set time
Phase reversal Phase rotation inhibit
Motor Loss Motor or output open cct
CT fault Fault with CT’s
Line Freq/Phase Problem with supply
Network Timeout Network Fault
Remote Input Forced trip from external source
Human Interface Module (HIM):
Type: Local or remote mountable (IP66)
Display: Backlit LCD (Blue) , English
Menu: Coded & English
Menu Protected: Selectable user access code
Cable type: Ribbon or Cat ‐ 5
Essential Services Over ‐ ride (ESO):
Selectable Digital input with 24Vdc logic.
Battery:
Type: CR1220