Zener SMARTSTART 6000, Инструкция по эксплуатации

Страница: 39 / 57

Programming
Technical Manual: Smartstart
®
6000 IMI0042 rev K
Page 36
Trip (Warning) codes & messages
A warning message will have a ‘W’ in place of the ‘T’ for
the following messages.
CODE/Message Description
T00 NO TRIP ALM No fault or trip has occurred.
T01 PSU LOW VOLT
Control supply voltage low. Check
control voltage.
T02 LINE FREQ Line supply frequency out of range while
motor running.
T03 LINE PH FLT 3 Phase supply problem, one phase
open. Check L1; L2; L3.
T04 PHS ROTATION Line Phase sequence in wrong direction –
User selectable. See P03 page 23.
T05 MTR 3/6 WIRE
Wiring detected different to motor
wiring setting. Check motor wiring.
T06 NET T/O Loss of communications while network
controlling motor.
T07 CT PHASING Incorrect CT phasing and/or insufficient
motor current. Check correct installation
of external CT’s (6 wire only). Check CT
phasing under the diagnostics menu to
check or help identify the error.
T10 START FAILED
Motor did not start.
T11 MTR STUCK ON Unexpected motor current detected
while off. Check wiring, relay
configuration and bypass contactor.
T13 MOTOR LOSS Motor current lost in all 3 phases. Check
Motor and motor wiring.
T14 BYPASS FAULT Bypass Contactor failed to close or
opened unexpectedly.
T15 BP POLE FLT
Bypass Contactor failed to close or
opened unexpectedly. 3 Phase/pole
fault.
T20 STR OVERCURR
Starter instantaneous over current while
up to speed.
T21 STR OVERTEMP
Starter heatsink over temperature.
T22 STR TEMP FLT Starter heatsink temperature sensor
fault.
T23 STR OVERLOAD Starter thermal overload. Motor or load
problem, start time longer than normal.
Excessive starts per hour. Insufficient
start torque and/or current limit too low
– check settings. Ambient temperature
rating exceeded or Starter rating
exceeded.
T24 MOTOR STALL Motor Stalled, current after start >300%
for 3 seconds. Check motor, load and
starter settings.
T25 VOLT IMBAL
Voltage imbalance as per user setting.
See P20 page 23. Check supply
T26 CURR IMBAL
Current imbalance as per user setting.
See P30 page 24. Check supply and
motor.
T30 MTR OVERLOAD
Motor thermal overload trip as per user
setting. See page 20. Incorrect overload
class (& starter rating). Motor or load
problem. Excessive starts per hour for
overload class selected. Insufficient start
torque and/or current limit too low –
check settings.
T31 MTR OVERTEMP Motor over temperature from the
thermistor input. See P02 page 23. Check
Motor and Load.
CODE/Message Description
T32 MTR TEMP FLT Motor thermistor sensor fault
detected. Check thermistor
and wiring.
T33 MTR OVERCURR Over current trip as per user
setting. See P50 page 25.
T34 MTR UNDERCURR Under current trip as per user
setting. See P40 page 24.
T35 MTR OVERTORQ
Over torque trip as per user
setting. See P70 page 25
T36 MTR UNDERTORQ Under torque trip as per user
setting. See P60 page 25.
T37 D1 INPUT ALM Trip initiated from external
source connected to Digital
input 1 .
T38 D2 INPUT ALM Trip initiated from external
source. connected to Digital
input 2.
T41 ACC OVERTIME Acceleration time has
exceeded set time as per user
setting. See P10 page 23.
Motor or load problem, start
time longer than normal.
Insufficient start torque and/or
current limit too low – check
settings.
T42 ESO MODE Warning Message when
Essential Services Over ‐ ride is
requested.
T43 A/R LOCKOUT Auto Restart Lockout – Auto
restarts exhausted or final trip
T50 MTR AMPS CFG
Motor Amps configuration
Error – Check and adjust motor
Amps and/or motor wiring.
T60 MOTOR FAULT
Current not detected in
multiple phases during
breakaway firing.
T61 T1 PHASE FLT
Current not detected in single
phase (T1/M1) during
breakaway firing.
T62 T2 PHASE FLT
Current not detected in single
phase (T2/M2) during
breakaway firing.
T63 T3 PHASE FLT
Current not detected in single
phase (T3/M3) during
breakaway firing.
T40 BRAKE FAIL
Brake input indicates External
Brake is ON while motor
Starting/Running.
.