Zener SMARTSTART 6000, Инструкция по эксплуатации

Страница: 48 / 57

Appendix A
Indicative parameters for different load types
Technical Manual: Smartstart
®
6000 IMI0042 rev K
Page 45
1. Pump (3 wire/Bypass with No Soft Stop)
Factory defaults are intended for general pumping/fan
application with no Soft Stop. Enter motor parameters
as per motor nameplate.
2. Submersible Pump
(3 wire/Bypass with No Soft Stop)
Factory defaults are intended for general pumping
application with no Soft Stop. The acceleration time
needs to be reduced to 3secs or as per pump/motor
manufacturers recommendations. Enter motor
parameters as per motor nameplate.
Ref Page Parameter Setting (factory Default)
C11 22 Accel time 3sec (10s)
M01 21 Motor Amps ‘Nameplate Motor FLC’
M02 21 Motor Volts ‘Nameplate Motor Volts’
M03 21 Motor PF ‘Nameplate Motor PF’
3. Pump :(3 wire/Bypass with Soft Stop)
Factory defaults are intended for general pumping
application with no Soft Stop. Enter motor parameters
as per motor nameplate. Adjust the ‘Release Torque’
and ‘Decel time’ to achieve the required soft stop.
Ref Page Parameter Setting (factory Default)
C21 22 Decel time *15sec (0s)
C22 22 Release Torque *2% (2%)
M01 21 Motor Amps ‘Nameplate Motor FLC’
M02 21 Motor Volts ‘Nameplate Motor Volts’
M03 21 Motor PF ‘Nameplate Motor PF’
4. Fan :(3 wire/Bypass)
Factory defaults are intended for general pumping
application which is similar to that required for a fan.
However, the Accel time may need to be increased to
allow for longer ramp times of high inertia fans. The
Motor Overload Class may also need to be increased
with the extended ramp of high inertia fans. Enter
motor parameters as per motor nameplate.
Ref Page Parameter Setting (factory Default)
C11 22 Accel time 15+ (10s)
P01 23 Motor Overload Class 10 /Class 20 (10)
M01 21 Motor Amps ‘Nameplate Motor FLC’
M02 21 Motor Volts ‘Nameplate Motor Volts’
M03 21 Motor PF ‘Nameplate Motor PF’
5. Conveyor: (3 wire/Bypass)
Factory defaults are preset for a variable torque load.
The Torque settings will need to be adjusted for a
constant torque type load. Enter motor parameters as
per motor nameplate.
Ref Page Parameter Setting (factory Default)
C12 22 Start Torque 80% (30%)
C13 22 Final Torque 150% (130%)
A21 29 Accel profile Linear (Squared)
P01 23 Motor Overload Class 20 (10)
M01 21 Motor Amps ‘Nameplate Motor FLC’
M02 21 Motor Volts ‘Nameplate Motor Volts’
M03 21 Motor PF ‘Nameplate Motor PF’
6. Compressor: (3 wire/Bypass)
Factory defaults are preset for a variable torque load.
The Torque settings will need to be adjusted for a
constant torque type load. Enter motor parameters as
per motor nameplate
.
Ref Page Parameter Setting (factory Default)
C12 22 Start Torque 60% (30%)
C13 222 Final Torque 130% (130%)
A21 29 Accel profile Linear (Squared)
P01 23 Motor Overload Class 20 (10)
M01 21 Motor Amps ‘Nameplate Motor FLC’
M02 21 Motor Volts ‘Nameplate Motor Volts’
M03 21 Motor PF ‘Nameplate Motor PF’
7. Suggested Protection Settings
Below are suggested settings to provide additional
protection of the motor and load. These are general
settings and should be further tuned to suit the
application and load conditions.
Ref Page Parameter Setting (factory Default)
P01 23 Motor Overload Class 10a/10/20 (10)
P02 23 Motor O/Temp Thermistor (Disabled)
P03 23 Phase Rotation 1 ‐ 2 ‐ 3 (Disabled)
P10 23 Accel O/Time Trip / 5s (Disabled)
P20 24 Volt Imbal. Trip / 25% / 5s (Default)
P30 24 Current Imbal. Trip / 25% / 10s (Default)
P41 24 Under Current Trip / 50% / 10s (Disabled)
P70 25 Over Torque Trip / 110% / 10 s (Disabled)