Zeiss EVO Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 180

Zeiss EVO Скачать руководство пользователя страница 98

5 First Operating Steps | 5.7 Working with Specific Specimen Types

ZEISS

Recommended

Parameters

The following parameters are recommended for hydrated specimens. The values given are only
suggestions and the operator may find that different values will give better information for the
types of specimens that are being investigated.

Parameter

EP mode for cooled hy-
drated specimens

EP mode for hydrated
specimens

20 kV

20 kV

I Probe

300 pA

300 pA

8.5 mm

5 mm

Filament

Fil I

set to second peak

Fil I

set to second peak

Mid-column aperture

750 μm

750 μm

Pressure-limiting aperture

100 μm EP aperture

100 μm EP aperture

Beamsleeve aperture

500 μm

500 μm

Detector

Scanning parameters

Cycle time ≥ 20 s

Cycle time ≥ 20 s

Chamber pressure

650 Pa to slow dehydration

2500 Pa to 3000 Pa to retain
water at ambient tempera-
ture (20 °C to 30 °C)

Temperature

Temperature of the speci-
men to retain water at
650 Pa = 1 °C (controlled by
the Peltier coolstage)

–

5.7.3.1 Installing or Deinstalling the EP and Beemsleeve Apertures

To use the optional EP mode, you need to install the EP and beamsleeve pressure-limiting aper-
tures under the objective lens.

Additionally, you need to select the 750 μm mid-column aperture and adjust some settings in
SmartSEM.

Pressure-limiting aperture

mid-column aperture

None (HV mode)

20 μm or 30 μm

100 μm EP aperture

and 500 μm or 1000 μm beamsleeve aper-
ture

750 μm

Parts and Tools



100 μm EP aperture (upper aperture assembly, 354720-9309-000)



Beamsleave aperture 500 μm (lower aperture assembly, 354720-0266-000), recommended



Beamsleave aperture 1000 μm (lower aperture assembly, 354720-0267-000), alternatively



Aperture removal tool (350700-0692-000)



Upper aperture tool (354720-9310-009)



Lower aperture tool (354720-9297-009)

98

Instruction Manual ZEISS EVO | en-US | Rev. 10 | 354706-0780-006

«
...
96
97
98
99
100
...
»

Содержание EVO





















































































































































































Отзывы:

Нет отзывов