Zeiss EVO Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 180

Zeiss EVO Скачать руководство пользователя страница 138

7 Troubleshooting | 7.2 Column

ZEISS

NOTICE

Contamination by dust particles or fingerprints

Dust particles or skin grease can cause contaminations, which lead to flashovers or to bad vac-
uum.

4

Wear lint-free gloves throughout the whole procedure of replacing the filament.

Parts and Tools



EVO firing unit for tungsten filaments (350071-2832-000) including a Wehnelt assembly and a
box of ten standard tungsten filaments. Only used when replacing LaB₆ with tungsten fila-
ments.



Lint-free gloves



Can of compressed air



Adjust key (350061-1904-000)



Hex key, 1.5 mm

Procedure

1. If the filament is not pre-aligned, insert the tensator spring into the firing unit.

INFO:

The tensator spring washer is not designed to be used in combination with pre-

aligned filaments. If you install the tensator spring washer in combination with a pre-
aligned filament, then the filament height is incorrect. If you install a pre-aligned filament,
then do not install the tensator spring washer.

2. Align the slot at the side of the filament holder

with the pin inside the firing unit.

3. Insert the new filament holder into the firing

unit.

7.2.2.4.2 Installing the Brass Retaining Washer | Tungsten (Pre-Aligned)

NOTICE

Contamination by dust particles or fingerprints

Dust particles or skin grease can cause contaminations, which lead to flashovers or to bad vac-
uum.

4

Wear lint-free gloves throughout the whole procedure of replacing the filament.

138

Instruction Manual ZEISS EVO | en-US | Rev. 10 | 354706-0780-006

«
...
136
137
138
139
140
...
»

Содержание EVO





















































































































































































Отзывы:

Нет отзывов