Zeiss EVO Скачать руководство пользователя страница 133

Страница: 133 / 180

ZEISS

7 Troubleshooting | 7.2 Column

Procedure

1. Take a new pre-aligned filament holder from

the box.

2. Use the can of compressed air to blow out any

dust particles from the filament holder and the
firing unit.

The new filament holder is ready for installation.

7.2.2.3 Tungsten (Not-Pre-Aligned) and LaB₆

7.2.2.3.1 Disassembling the Filament Holder | Tungsten (Not Pre-Aligned) and LaB₆

Before you can install a new filament to the filament holder, you first need to disassemble the fila-
ment holder.

NOTICE

Contamination by dust particles or fingerprints

Dust particles or skin grease can cause contaminations, which lead to flashovers or to bad vac-
uum.

Wear lint-free gloves throughout the whole procedure of replacing the filament.

Parts and Tools



Lint-free gloves



Hex key, 1.5 mm (000000-0151-883)



Adjust key (350061-1904-000)

Prerequisite

The firing unit is disassembled.

Procedure

1. Use a hex key 1.5 mm to remove the four

screws.

INFO:

These screws have rounded ends.

Instruction Manual ZEISS EVO | en-US | Rev. 10 | 354706-0780-006

133

Содержание EVO





















































































































































































Результаты поиска

Содержание EVO

Отзывы:

Zeiss EVO, Инструкция по эксплуатации, Страница: 133 / 180

Результаты поиска

Содержание EVO

Отзывы: