Zeiss EVO Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 180

Zeiss EVO Скачать руководство пользователя страница 163

ZEISS

9 Technical Data and Conformity | 9.4 Performance Data and Specifications | EVO 15

Parameter

Description

§

Z = 50 mm

§

T = −10° to 90°

§

R = 360° continuous

INFO:

The movements may be reduced by specimen size, operating

conditions, and accessories attached.

Specimen height:

max. 145 mm (with the ZTR module removed)

Specimen diameter:

max. 250 mm

Specimen weight:

Standard stage

§

0.5 kg (full motion)

§

2 kg (not tilted)

§

5 kg (only XY motion)

Large Z stage (optional)

§

2 kg (not tilted)

§

5 kg (only XY motion)

Specimen current monitor

with integrated

Touch Alarm

(audible

touch alarm warning with on-screen message)

Specimen mounts:

One 9x specimen holder for 13 mm diameter

stubs included in base tool configuration, various specimen holders
available as option

Vacuum range

Vacuum modes

§

HV mode: lower than 2 mPa (2 × 10⁻⁵ mbar)

§

VP mode (optional): 10–400 Pa

§

EasyVP mode (optional): 10–133 Pa

§

EP mode (optional): 10–3000 Pa

Detection System

Parameter

Description

Chamber detectors

SE detector:

Everhart-Thornley SE detector with optically coupled photomultiplier;
collector bias adjustable from −250 to +400 V

VPSE detector (optional)

(only for VP mode):

Fourth generation variable pressure secondary electron detector for
imaging in VP mode with up to 85 % improvement in Weber contrast
ratio

C2D detector (optional)

(only for VP mode):

Cascade Current Detector with floating amplifier electronics, for en-
hanced imaging in Variable Pressure mode up to 133 Pa. Delivers de-
tail at low kV for specimens that demand higher pressures, e.g. poly-
mers, bio specimens, pharmaceuticals, powders, and fibers. Enhanced
signal-to-noise ratio versus VPSE detector.

C2DX (optional)

(only for VP mode):

Extended Cascade Current Detector

Instruction Manual ZEISS EVO | en-US | Rev. 10 | 354706-0780-006

163

«
...
161
162
163
164
165
...
»

Содержание EVO





















































































































































































Отзывы:

Нет отзывов