Zeiss EVO Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 180

Zeiss EVO Скачать руководство пользователя страница 161

ZEISS

9 Technical Data and Conformity | 9.4 Performance Data and Specifications | EVO 15

Parameter

Value

Ampere interrupting capacity (AIC)

Min. 10,000 A

rms

Location

Requirements

Parameter

Requirement

Installation site

Exclusively inside buildings

Recommended
room size

Min. 3.6 m × 4.0 m × 2.3 m

Service area

Min. 0.8 m at each side

Entrance

Min. 0.8 m wide

Hallways

Min. 1.0 m wide

Corners

Min. 1.2 m wide

Transport ways

Free of staircases

Installation cate-
gory

II

Floor stability

> 1000 kg/m²

Exhaust Line

If toxic chemicals or biological specimens are used an exhaust line is recommended to remove the
waste gas of the pre-vacuum pump and to transmit it to the outside.

Nitrogen

Gaseous dry nitrogen is used to vent the specimen chamber during specimen exchange. The nitro-
gen can be taken either from a gas cylinder or from an in-house supply system.

Parameter

Requirement

Flow rate

Approx. 3 l/min for ventilation of specimen chamber with chamber
door open

Pressure

0.2–3.3 bar

Quality

4.6 with nitrogen content > 99.996 %

Connection hose

4 mm inside diameter. 10 m are delivered with the microscope.

Instrument con-
nection

Quick exchange connector. One is delivered with the microscope.

Compressed Air

Supply

Compressed air is used to operate several valves and the auto leveling system. The necessary com-
pressed air can be either generated by a compressor (part no. 345596-0000-000) or taken from a
gas cylinder or from an in-house supply system.

Environmental

Requirements

Parameter

Requirement

Electrical field

The microscope is a class A device (industrial). The microscope is de-
signed to operate in a controlled electromagnetic environment. This
means that devices with RF transmitters such as mobile phones or
DECT phones must not be used in close proximity.

Vibrations

Less than 6 μm/sec rms from 0–30 Hz

Less than 12 μm/sec rms above 30 Hz

Magnetic stray
fields

Max. 3 × 10⁻⁷ T (peak to peak) = 3 mG (peak to peak)

Acoustic noise

Less than 53 dB for frequencies up to 200 Hz

Instruction Manual ZEISS EVO | en-US | Rev. 10 | 354706-0780-006

161

«
...
159
160
161
162
163
...
»

Содержание EVO





















































































































































































Отзывы:

Нет отзывов