Zeiss EVO Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 180

Zeiss EVO Скачать руководство пользователя страница 8

1 General Information | 1.3 Further Applicable Documents

ZEISS

1.3 Further Applicable Documents

Please also take note of the following documents:

Brochures and

Certificates

For Brochures, ISO certificates, CSA certificates and EU declarations of conformity ask your ZEISS
Sales & Service Partner.

Installation

Requirements

For more details on technical data, refer to the corresponding Installation Requirements.

Local and National

health and safety

regulations

Local and national health and safety regulations should be adhered to for the site and the use of
the Microscope System.

Please consult with your ZEISS Sales & Service Partner in the event of these regulations conflicting
with the installation requirements of the Microscope System.

Safety data sheets

Observe the enclosed safety data sheets. The instructions and guidelines given in the respective
safety data sheets must be complied with.

Software

For detailed information on how to use SmartSEM, please refer to its Online Help or ask your
ZEISS Sales & Service Partner.

System and 3rd

Party Components,

Accessories

Information about the individual components, enhancements and accessories can be obtained
from your ZEISS Sales & Service Partner.

Also refer to the 3rd Party documentation of the manufacturer.

1.4 Contact

If you have any questions or problems, please contact your local ZEISS Sales & Service Partner or
one of the following addresses:

Headquarters

Phone:

+49 1803 33 63 34

Fax:

+49 3641 64 3439

Email:

[email protected]

Courses and training

Email:

[email protected]

ZEISS Portal

The ZEISS Portal (

https://portal.zeiss.com/

) offers various services that simplify the daily work with

your ZEISS systems (machines and software). It is constantly improved and extended to meet your
needs and requirements better.

ZEISS Sales & Service Partner

You can find a ZEISS Sales & Service Partner in your area under

https://www.zeiss.de/mikroskopie/

website/forms/sales-and-service-contacts.html

.

Service Germany

Phone:

+49 7364 20 3800

Fax:

+49 7364 20 3226

Email:

[email protected]

8

Instruction Manual ZEISS EVO | en-US | Rev. 10 | 354706-0780-006

«
...
6
7
8
9
10
...
»

Содержание EVO





















































































































































































Отзывы:

Нет отзывов