Weather-Rite TT Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 205 / 205

SECTION 2 8 : T
HE
WEATHER-RITE ™ TT-S
ERIES
W
ARRANTY
199 of 198
WARNING
Read the Installation, Operation and Service Manual thoroughly before installation, operation or service.
OPERATING INSTRUCTIONS
1. Stop! Read all safety instructions on this information sheet.
2. Open the manual gas valve in the air handler supply line.
3. Turn on electric to the air handler.
4. Set temperature selector and, if equipped, thermostat, to desired
setting.
5. Set FAN switch to “ON”.
6. Set BURNER switch to “ON”.
1. Stop! Read all safety instructions on this information sheet.
2. Turn on electric to the air handler.
3. Set FAN switch to “ON”.
1. If equipped, set the thermostat to the lowest setting.
2. Set BURNER switch to “OFF”.
3. Set FAN switch to “OFF”.
1. If equipped, set the thermostat to the lowest setting.
2. Set BURNER switch to “OFF”.
3. Set FAN switch to “OFF”.
4. Turn off electric to the air handler.
5. Close the manual gas valve in the air handler supply line.
6. Call your registered contractor qualified in the installation and service
of gas-fired heating equipment.
Fire Hazard
Keep all flammable objects, liquids and vapors the
required clearances to combustibles away from
equipment.
Some objects can catch fire or explode when placed
close to equipment.
Failure to follow these instructions can result in
death, injury or property damage.
Installation Code and Annual Inspections: All installation and service of WEATHER-RITE ™ equipment must be performed by a contractor qualified in the installation and service of equipment sold and
supplied by Weather-Rite LLC and conform to all requirements set forth in the WEATHER-RITE
™
manuals and all applicable governmental authorities pertaining to the installation, service, operation
and labeling of the equipment. To help facilitate optimum performance and safety, Weather-Rite LLC recommends that a qualified contractor conduct, at a minimum, annual inspections of your
WEATHER-RITE
™ equipment and perform service where necessary, using only replacement parts sold and supplied by Weather-Rite LLC.
Air handlers are approved for installation up to 2000' (610 m).
For installations at elevations above 2000' (610 m), consult factory.
Further Information: Applications, engineering and detailed guidance on systems design, installation and equipment performance is available through WEATHER-RITE
™
representatives. Please
contact us for any further information you may require, including the Installation, Operation and Service Manual.
These products are not for residential use.
© 2017 Weather-Rite LLC All rights reserved. No part of this work covered by the copyrights herein may be reproduced or copied in any form or by any means – graphic,
electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems – without written permission
of Weather-Rite LLC.
Weather-Rite LLC
1100 Seven Mile Road NW
Comstock Park, MI 49321
Telephone: +1.612.338.1401
Fax: +1.6167840435
Toll Free: 800.589.3691
CLEARANCES TO COMBUSTIBLES
Clearances to combustibles for Models XT112 - XT130 are
12" (30.5 cm) on the control enclosure side and 6" (15.2 cm) on all
other surfaces.
Clearances to combustibles for models XT225 and XT230 are 6"
(15.2 cm) on all surfaces.
Clearances to combustibles do not denote clearances for
accessibility. Minimum clearance for access is 48" (122 cm) on all
models. Minimum clearance for accessibility applies to the control
enclosure, blower access panel and filter access panel
(when equipped).
TO OPERATE AS VENTILATOR
TO TURN OFF THE AIR HANDLER
IF THE AIR HANDLER WILL NOT OPERATE,
FOLLOW THESE INSTRUCTIONS, TO HELP
ENSURE YOUR SAFETY
www.weather-rite.com Printed in U.S.A. P/N 91040117 Rev C
Attach this information to the wall near the WEATHER-RITE
™
remote panel or equipment controls.