Volkswagen CJDA Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 553

background image

Renewing engine oil filter, engine codes CJDA, CJDD, CPYA,
CPYB, CPYC, CPYD, CPYE

Fill engine oil

.

● The engine oil must be changed regularly as per the specifi-

cations in the service schedule.

● The engine oil and filter change should always be carried out

in a specialist workshop as special tools and knowledge are
required. This also applies to the disposal of used oil. Volks-
wagen recommends that these tasks are carried out at a
Volkswagen dealership.

● Additives in the engine oil can cause new engine oil to dis-

colour quickly. This is normal and does not mean that the
engine oil should be changed more frequently.

1.2.1 Draining or extracting engine oil

Caution

◆

For engines with upright oil filter module, the oil filter
should be renewed before changing the engine oil.
When removing the filter element a valve is opened, the
oil in the filter housing automatically flows into crank-
case.

◆

The oil drain plug is fitted with a captive seal. Therefore,
the oil drain plug must always be renewed.

Special tools and workshop equipment required

◆

Used oil collection and extraction unit -V.A.G 1782-

◆

Cloth to absorb oil -VAS 6204/1-

Draining or extracting engine oil:

Carry out the following procedure:

– Extract engine oil using used oil collection and extraction

unit -V.A.G 1782-.

Or

– Remove oil drain plug.

– Let engine oil drain.

Note

Use a suitable container when draining the used oil. It must be
at least large enough to hold the entire quantity of engine oil re-
quired for refilling.

– Screw in oil drain plug together with seal hand-tight and then

tighten to specified torque.

– Fill engine oil, specification

.

Engine oil capacity:

Specified torques for oil drain plug:

Industriemotoren - Industrial Engines 2009

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

3

1 Engine oil

245

«
...
259
260
261
262
263
...
»

Содержание CJDA










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJDA

Бренд: Aerovent Страницы: 16

Бренд: de Gier Страницы: 26

Бренд: KSB Страницы: 52

ZA top SM210.60

Бренд: ZIEHL-ABEGG Страницы: 96

Бренд: Caple Страницы: 16

Бренд: Haas Страницы: 7

Бренд: Honda Страницы: 21

Бренд: Honda Страницы: 56

B21 ADAM DRAKE EDITION

Бренд: O.S. Speed Страницы: 4

Track Runner Series

Бренд: Wahlberg Страницы: 32

Бренд: Swiss Rotors Страницы: 26

Бренд: Daewoo Страницы: 126

Бренд: Jamara Страницы: 2

Бренд: YewdaleDefiant Страницы: 8

Бренд: FeiaoModel Страницы: 8

Бренд: Detroit Diesel Страницы: 442

Бренд: Doosan Страницы: 206

Бренд: Ruggerini Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды