Volkswagen CJDA Скачать руководство пользователя страница 298 | Manualshive

Страница: 298 / 553

background image

◆

Refractometer -T10007 A-

Note

Read precise value for the following tests at bright/dark boun-
dary. Using a pipette, place a drop of water on the glass to im-
prove the readability of the bright/dark boundary. The bright/
dark boundary can be clearly recognised on the “WATERLINE”.

– Check concentration of coolant additive using refractometer

-T10007- (refer to operating manual) or refractometer
-T10007 A- (refer to operating manual).

The scale -1- of the refractometer is calibrated for coolant addi-
tives G 11; G 12; G 12+ und G 12++.

The scale -2- is only calibrated for coolant additive G13.

Note

◆

The frost protection must be guaranteed to approx. -25 °C.

◆

If a stronger anti-freeze mixture is necessary due to harsher
weather conditions, it can be increased using G 12+ or G
12++. But increase it only to 60 % (frost protection to approx.
-40°C), otherwise frost protection and cooling effectiveness
are reduced again.

– If frost protection is insufficient, drain coolant and top up with

coolant additive G 12++

Note

Observe environmental regulations for disposal.

Caution

Only distilled water may be used for mixing. Tap or well wa-
ter does not have the required quality to ensure the effec-
tiveness of coolant.

– Check coolant additive concentration after road test again.

1.4.2 Checking coolant level, replenishing cool-

ant additive if necessary

– Check coolant level in coolant expansion tank when the en-

gine is cold.

◆

Delivery inspection: coolant level above “min.” marking.

◆

Inspection service: coolant level above “min.” marking.

– If coolant is too low, add required amount according to mix-

ture ratio.

Note

If fluid loss is greater than can be expected through normal use,
determine source and rectify (repair measure).

3

Industriemotoren - Industrial Engines 2009

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

282

Repair Group 19 - Cooling

«
...
296
297
298
299
300
...
»

Содержание CJDA










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJDA

Бренд: Wartsila Страницы: 168

E-8 DIESEL ENGINE

Бренд: M.T.H. Страницы: 36

Бренд: Danfoss Страницы: 77

Бренд: RenewAire Страницы: 28

Бренд: Champion Power Equipment Страницы: 29

Бренд: Saito Страницы: 27

Бренд: Man Страницы: 18

Бренд: Yamaha Страницы: 51

Бренд: MINN KOTA Страницы: 3

Бренд: MINN KOTA Страницы: 4

Бренд: Nederman Страницы: 44

CROUZET 801400TNI21

Бренд: Innovista Sensors Страницы: 39

Бренд: YS Страницы: 2

Бренд: FIAMA Страницы: 7

Бренд: Wilesco Страницы: 4

Бренд: Winterthur Gas Страницы: 495

Бренд: HAMPTON BAY Страницы: 17

Бренд: Detroit Diesel Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды