manualshive.com logo in svg

Volkswagen CJDA, Руководство по ремонту


Поделиться
Скачать
background image

Removing and installing engine

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

133

1

Removing and installing engine

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

133

1.1

Notes on removing

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

134

1.2

Securing engine to assembly stand

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

136

1.3

Notes on installing

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

136

1.4

Specified torques

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

137

1.5

Additional information and assembly work for power units with air conditioning system

 . . .

137

Crankshaft group

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

138

1

Dismantling and assembling engine

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

138

1.1

Assembly overview - poly V-belt drive, with air conditioner compressor

 . . . . . . . . . . . . . . . . . . . . .

140

1.2

Assembly overview - poly V-belt drive, without air conditioner compressor

 . . . . . . . . . . . . . . . . .

141

1.3

Removing and installing or renewing poly V-belt

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

141

1.4

Poly V-belt: Check condition

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

143

1.5

Removing and installing poly V-belt tensioner, engines with air conditioner compressor
only

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

143

1.6

Removing and installing ancillary bracket

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

144

1.7

Assembly overview - toothed belt drive, engine codes CJDA, CJDD, without crankshaft
seal

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

146

1.8

Removing and installing engine bracket

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

148

1.9

Assembly overview - toothed belt drive, engine codes CPYA, CPYB, CPYC, CPYE, with
crankshaft seal

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

149

1.10

Removing and installing toothed belt guard with inspection cover for checking tension of
toothed belt

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

150

1.11

Performing visual check of toothed belt tension

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

151

1.12

Assessing wear on tensioning roller and belt pulleys

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

152

1.13

Wear of high-pressure pump pulley

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

152

1.14

Assessing wear

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

153

1.15

Removing and installing crankshaft protective cover

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

155

1.16

Assembly overview - crankcase, engine codes CJDA, CJDD

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

156

1.17

Assembly overview - crankcase, engine codes CPYA, CPYB, CPYC, CPYD, CPYE

 . . . . . .

157

2

Removing and installing sealing flange and flywheel

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

158

2.1

Assembly overview - Sealing flange, belt pulley end

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

159

2.2

Renewing crankshaft oil seal - pulley end

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

161

2.2.1

Removing

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

162

2.2.2

Installing

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

163

2.3

Removing and installing crankshaft sealing flange, pulley end

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

164

2.3.1

Removing

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

165

2.3.2

Installing

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

166

2.4

Assembly overview - sealing flanges and flywheel

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

167

2.5

Renewing crankshaft sealing flange - flywheel end

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

169

10 -

13 -

3

Industriemotoren - Industrial Engines  2009 

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

vi

Contents

Содержание CJDA










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJDA

ULPOWER UL390i Maintenance Manual preview
UL390i
Бренд: ULPOWER Страницы: 20
Briggs & Stratton Vanguard 290000 Operator'S Manual preview
Vanguard 290000
Бренд: Briggs & Stratton Страницы: 68
Polini THOR 190 HF Use And Maintenance Manual preview
THOR 190 HF
Бренд: Polini Страницы: 34
Exalto MD1 223BDC Manual preview
MD1 223BDC
Бренд: Exalto Страницы: 28
Key Automation RAY2524 Instructions And Warnings For Installation And Use preview
RAY2524
Бренд: Key Automation Страницы: 44
Lycoming AIO-320 Operator'S Manual preview
AIO-320
Бренд: Lycoming Страницы: 83
Briggs & Stratton 093J00 Operator'S Manual preview
093J00
Бренд: Briggs & Stratton Страницы: 60
Lycoming TEO-540-C1A Maintenance Manual preview
TEO-540-C1A
Бренд: Lycoming Страницы: 568
Hacker SKALAR SC Series Manual preview
SKALAR SC Series
Бренд: Hacker Страницы: 2
Robin America EY15-3 Service Bulletin preview
EY15-3
Бренд: Robin America Страницы: 23
Mitsubishi 4D56 User Manual preview
4D56
Бренд: Mitsubishi Страницы: 76
O.S. engine GT55 Owner'S Instruction Manual preview
GT55
Бренд: O.S. engine Страницы: 18
O.S. engine MAX 140RX FI Owner'S Instruction Manual preview
MAX 140RX FI
Бренд: O.S. engine Страницы: 24
DANA BREVINI D 072 Series Installation And Maintenance Manual preview
BREVINI D 072 Series
Бренд: DANA Страницы: 58
DANA BREVINI M Series Installation And Maintenance Manual preview
BREVINI M Series
Бренд: DANA Страницы: 40
Honda GCV160 Owner'S Manual preview
GCV160
Бренд: Honda Страницы: 88
LRP electronic Z.28R Spec.3 Pullstart User Manual preview
Z.28R Spec.3 Pullstart
Бренд: LRP electronic Страницы: 3
Motion CM-35 Manual preview
CM-35
Бренд: Motion Страницы: 75

Бренды по названию

Популярные бренды

Загрузить еще бренды