manualshive.com logo in svg

Volkswagen CJDA, Руководство по ремонту


Поделиться
Скачать
background image

● All electrical consumers must be switched off.

● Earth connections OK

Procedure

– Connect connector of diagnostic cable -VAS 5051B/1- or re-

mote head to diagnostic connection.

– Depending on the function required, do the following:

◆

Switch on ignition, or

◆

start engine; available diagnosis functions.

 Note

◆

If the display remains blank, check the voltage supply for the
diagnostic connector using the current flow diagram.

◆

If the display is not as shown in the procedure, refer to the

⇒ 

 Operating manual for the vehicle diagnosis system.

Select operating mode

– Press button on display for “Vehicle self-diagnosis”.

Select vehicle system

– Press “01 - Engine electronics” button on display.

The identification and coding of the engine control unit are
shown on the display.

If the coding does not match:

– Check control unit coding.

Select diagnostic function

All the available diagnosis functions are shown on the display.

– Press key on display for the desired function.

 Note

For the function “011-Measured values”, the display zones are
listed from top to bottom.

Available functions when using the vehicle diagnosis, testing
and information system.

1.4

Connecting test box to check lines

 Note

◆

The adapter cables -V.A.G 1598/39-1- and
-V.A.G 1598/39-2- are used in conjunction with the test box
-V.A.G 1598/42- to check the lines between the relevant
components and the engine control unit.

◆

The contacts on the engine control unit are distributed over
two different wiring harnesses.

◆

Depending on the component to be checked, the test is per-
formed on the wiring harness with a 60-pin connector or with
a 94-pin connector.

3

Industriemotoren - Industrial Engines  2009 

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

24

Repair Group  01 - Vehicle self-diagnosis

Содержание CJDA










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJDA

FAZUA Evation Quick Manual preview
Evation
Бренд: FAZUA Страницы: 76
Eaton Char-Lynn H Series Manual preview
Char-Lynn H Series
Бренд: Eaton Страницы: 13
BRP Johnson BJ25E4SUC Service Manual preview
Johnson BJ25E4SUC
Бренд: BRP Страницы: 265
Kober AL-KO Instructions For Use Manual preview
AL-KO
Бренд: Kober Страницы: 112
Siemens Simodrive 611 Installation Manual preview
Simodrive 611
Бренд: Siemens Страницы: 4
Siemens SIMOTICS A-1FV5 Operating Instructions Manual preview
SIMOTICS A-1FV5
Бренд: Siemens Страницы: 66
Siemens SIMOGEAR 2332 Original Mounting And Operating Instructions preview
SIMOGEAR 2332
Бренд: Siemens Страницы: 56
Siemens SIMODRIVE POSMO A Function Manual preview
SIMODRIVE POSMO A
Бренд: Siemens Страницы: 58
Siemens SIMOTICS GP Operating Instructions Manual preview
SIMOTICS GP
Бренд: Siemens Страницы: 100
Siemens Simotics HV C 1NA14544WA600AG0-Z Operating Instructions And Installation Instructions preview
Simotics HV C 1NA14544WA600AG0-Z
Бренд: Siemens Страницы: 112
Siemens SIMOTICS DP 1PC13 Operating Instructions Manual preview
SIMOTICS DP 1PC13
Бренд: Siemens Страницы: 100
Siemens SIMOTICS DP 1PC134 Operating Instructions Manual preview
SIMOTICS DP 1PC134
Бренд: Siemens Страницы: 120
Siemens SIMOTICS HT Series Operating Instructions & Installation Instructions preview
SIMOTICS HT Series
Бренд: Siemens Страницы: 128
Siemens SIMOTICS HV M Operating Instructions Manual preview
SIMOTICS HV M
Бренд: Siemens Страницы: 136
Siemens SIMOTICS DC 1GH5 Operating And Installation Instructions preview
SIMOTICS DC 1GH5
Бренд: Siemens Страницы: 130
Siemens SIMOTICCS A 1FU9 Operating Instructions Manual preview
SIMOTICCS A 1FU9
Бренд: Siemens Страницы: 126
Siemens SIMOTICS DP Operating Instructions Manual preview
SIMOTICS DP
Бренд: Siemens Страницы: 142
Siemens SIMOTICS DP series Operating Instructions Manual preview
SIMOTICS DP series
Бренд: Siemens Страницы: 150

Бренды по названию

Популярные бренды

Загрузить еще бренды