Volkswagen CJDA Скачать руководство пользователя страница 318

Страница: 318 / 553

Yes

⇒

“Step 3 (There are filings in fuel tank and strainer)” on

page 302

⇒

“Step 4 (There are no filings in fuel tank and strainer)”

on page 303

1.3.2 Step 2 (Engine was not started with incor-

rect fuel)

– Empty fuel tank as far as possible via fuel filler neck using

fuel extractor -VAS 5190-.

Engine codes CJDA, CJDD

Pull off fuel supply line to high-pressure pump ahead of strainer.

Engine codes CPYA, CPYB, CPYC, CPYD, CPYE

Pull fuel supply line from fuel pump -V393 (Inline EKP)- to fuel
filter off fuel filter.

Continuation for all engine codes

– Put open end of line into a suitable container.

– Perform final control diagnosis, and activate fuel pump,

⇒

Page 89

, final control diagnosis.

Note

The fuel pump is now activated.

– Repeat procedure, if necessary, until fuel tank is completely

empty.

– Fill fuel tank with 5 litres of diesel fuel.

– Completely empty fuel tank again as described above.

– Reconnect fuel supply line to fuel filter.

– Fill up machine, and perform road test.

End

1.3.3 Step 3 (There are filings in fuel tank and

strainer)

– Clean fuel tank in accordance with manufacturer specifica-

tions.

– Clean strainer.

– Fill fuel tank with 5 litres of diesel fuel.

– Completely empty fuel tank again as described above.

– Renew following high-pressure components:

◆

◆

◆

Fuel rail included

◆

◆

Fuel return lines (overflow oil lines)

⇒

Page 362

Industriemotoren - Industrial Engines 2009

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

302

Repair Group 20 - Fuel supply system

Содержание CJDA










































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CJDA

Отзывы:

Похожие инструкции для CJDA

Бренды по названию

Популярные бренды

Volkswagen CJDA, Руководство по ремонту

Результаты поиска

Содержание CJDA

Отзывы:

Похожие инструкции для CJDA

Бренды по названию

Популярные бренды