manualshive.com logo in svg

Volkswagen CJDA, Руководство по ремонту


Поделиться
Скачать
background image

Caution

Only distilled water may be mixed with G12 plus-plus. The
use of distilled water ensures optimum protection against
corrosion.

 Note

◆

Use only coolant additive G 12 plus-plus in accordance with
TL VW 774 G.

◆

It is only permissible to use distilled water for mixing.

◆

Coolant additives marked “in accordance with TL VW 774 G”
prevent lime accretion, frost damage and corrosion. More-
over, the boiling temperature is raised. Therefore, the cool-
ing system must be filled all year round with coolant additive.

◆

Because of its higher boiling point, the coolant improves en-
gine reliability under heavy loads, particularly in countries
with tropical climates.

◆

Frost protection is required down to about -25°C (in coun-
tries with arctic climates: down to about -35°C).

◆

The coolant concentration must not be reduced by adding
water even in warmer seasons and in warmer countries. The
coolant additive concentration must be at least 40%.

◆

If a stronger anti-freeze mixture is necessary due to harsher
weather conditions, it can be increased using G 12 plus-
plus. It may be strengthened, however, only to 60% (anti-
freeze protection to about -40°C). Otherwise, the antifreeze
protection will be reduced again and the cooling effect will be
impaired.

◆

If radiator, heat exchanger, cylinder head or cylinder head
gasket is renewed, do not reuse old coolant.

◆

The refractometer -T10007- is recommended for determining
the current anti-freeze density.

Recommended mixture ratios

Frost protec-

tion

to

Anti-freeze

proportion

G 12 plus-plus

1)

Distilled

water

1)

-25 °C

40 %

3.2 l

4.8 l

-35°C

50 %

4.0 l

4.0 l

1)

The quantity of coolant may vary depending upon equipment. Observe

specifications of machine manufacturer.

– Secure lower coolant hose to connecting piece of radiator.

3

Industriemotoren - Industrial Engines  2009 

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

286

Repair Group  19 - Cooling

Содержание CJDA










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CJDA

BAFANG H550 Manual preview
H550
Бренд: BAFANG Страницы: 5
Mack E7 Service Manual preview
E7
Бренд: Mack Страницы: 303
HunterDouglas M40 TE Instructions And Warnings For Installation And Use preview
M40 TE
Бренд: HunterDouglas Страницы: 20
Kohler 100EFOZC Installation Instructions Manual preview
100EFOZC
Бренд: Kohler Страницы: 12
GGP WBE 0701 Workshop Manual preview
WBE 0701
Бренд: GGP Страницы: 56
Fireye NEXUS NX50-1 Installation Manual preview
NEXUS NX50-1
Бренд: Fireye Страницы: 8
Wisconsin Motors V460D Repair Manual preview
V460D
Бренд: Wisconsin Motors Страницы: 46
DLE DLE-111 User Manual preview
DLE-111
Бренд: DLE Страницы: 4
Toro 159cc Service Manual preview
159cc
Бренд: Toro Страницы: 46
YS FZ70S Operator'S Manual preview
FZ70S
Бренд: YS Страницы: 4
Chicago Pneumatic M2501-5500-KSL Instruction Manual preview
M2501-5500-KSL
Бренд: Chicago Pneumatic Страницы: 88
DETROIT MBE 900 Operator'S Manual preview
MBE 900
Бренд: DETROIT Страницы: 64
Yanmar 6LT Series Operation Manual preview
6LT Series
Бренд: Yanmar Страницы: 76
Yanmar 6LY2-STE Service Manual preview
6LY2-STE
Бренд: Yanmar Страницы: 234
DLE DLE120-T4 User Manual preview
DLE120-T4
Бренд: DLE Страницы: 4
DLE DLE-85 Operator'S Manual preview
DLE-85
Бренд: DLE Страницы: 24
sati GB755 Installation And Maintenance Instructions Manual preview
GB755
Бренд: sati Страницы: 19
Cors-Air M25 Manual preview
M25
Бренд: Cors-Air Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды