VeEX VePAL TX300 Скачать руководство пользователя страница 278

Страница: 278 / 421

Quick Test Setup

Fill out each screen and press

NEXT

to proceed to the next page or

Previous

to go back to the previous screen.

Step 1:

Select the router test interface. "Local unit" denotes a router wrap test while "end-to-end" conducts an end-to-end test.

The frame size for each option listed below is 256 bytes. The following options are available:

1G-1G on local unit: 1G interface is always set to 100% of the line rate.

1G-10G on local unit: 10G interface is always set to 10% of the line rate.

1G-10G with remote test unit: For Copper or Fiber, Controller is set to 100% of the line rate; remote is 100% of the line

rate.

10G-10G with remote test unit: Controller is set to 100% of the line rate; remote is 100% of line rate.

Step 2:

Select the copper/fiber ports to be used in the test. If the copper port is selected, configure the port settings: Auto

Negotiation, Advertisement and Flow Control.

Step 3:

The wavelength for the test ports in use will display at the beginning of Step 3.

Step 4&5: Entering the IP Address

Step 4:

Enter the local IP address for port 1. Press

Apply

and configure the subnet mask address. Press

Apply

and enter the

gateway address. At the end of Step 4, the screen will display a summary of the IP address, Subnet, and Gateway. Tap on any

of the corresponding fields to make any changes, if necessary.

Step 5:

Enter the IP address, Subnet, and Gateway for port 2, following the same procedure detailed in Step 4.

Step 6:

Review the settings for both ports. Press

Start

to begin testing. Pressing

Reconfigure

will restart the Quick Test Setup

and return the screen to Step 1.

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды