VeEX VePAL TX300 Скачать руководство пользователя страница 414

Страница: 414 / 421

Go back to top

Go back to TOC

17.2.2.6 Saving and Retrieving Files

At any time when the test is in progress or completed, press the

Save

key

on the rubber keypad to save test results.

Use the alphanumeric keyboard to name the file and press

Apply

to save the results and close the keyboard screen.

Saving and Naming Results

To access Saved results, access the

Files

Saved

menu on the left side toolbar.

Scroll down to

CPRI

index.

All previously saved CPRI results are listed. Tap on the results file name to open the file or choose to copy to USB, delete, or

rename the file.

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды