VeEX VePAL TX300 Скачать руководство пользователя страница 151

Страница: 151 / 421

SOH RX, which displays the bytes associated with the Section/LINE Overhead

POH RX, which displays the bytes associated with the Path Overhead

Summary, which displays the Path Traces (J0, J1, J2), APS (K1, K2), Synchronization status (S1), STS Path (C2), and VT

Path (v5) Signal Label bytes

SOH

Tapping the applicable byte enables an automatic decode – a byte description including the Hexadecimal and Binary value is

provided. For some bytes, an advanced decode of the various bits is also available.

Section Overhead

The following is a partial list of SOH bytes and their corresponding functions:

Section Layer

Framing Bytes (A1/A2)

The A1/A2 bytes indicate the beginning of the STM-N frame and provide a frame alignment pattern

A1 is the 1st framing byte: 11110110 (Hex F6)

A2 is the 2nd framing byte: 00101000 (Hex 28)

Both A1 and A2 bytes are unscrambled

The Frame Alignment Word of a STM-N frame is composed of (3 x N) A1 bytes followed by (3 x N) A2 bytes

A1 [Framing] Byte

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды