VeEX VePAL TX300 Скачать руководство пользователя страница 179

Страница: 179 / 421

Lower Order Matrix

Breaks down structured tributaries into their own channels, to bring more visibility and allow users to pinpoint the exact source of

a problem, or monitor a specific sub-channel. Its behavior is similar to the High order matrix.

Soft LED Section

This section provides a real-time visual summary of the selected tributary by means of soft LEDs and signal labels.

Solid green identify good status.

Solid red indicates a problem.

Intermittent red indicates a problem that occurred in the past that is no longer present. Use the Clear LED button to reset

the history indication.

Gray = not applicable.

OTN and SDH/SONET Soft LEDs

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды