manualshive.com logo in svg

VeEX VePAL TX300, Руководство пользователя, Страница: 207 / 421

Поделиться
Скачать
VeEX VePAL TX300 Скачать руководство пользователя страница 207

APS Test Procedure:

The TX300/e should be connected to a tributary port of network element or transmission system to ensure that the

switching time is measured for the service transported by the SONET network.

Ensure that no errors or alarms are present on the transmission system because this will impact the measurement.

The measurement will be triggered by an Alarm Indication Signal (AIS)

The TX300/e measures how long the AIS event remains present after the event is first recognized and will continue to

measure the total disruption time in the event of multiple disruptions.

Go back to top

 

Go back to TOC

10.2.7.2 APS Sequence

The associated K1/K2 sequence and received K1/K2 bytes may be captured.

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Отзывы:

Нет отзывов