VeEX VePAL TX300 Скачать руководство пользователя страница 172

Страница: 172 / 421

APS Test Procedure:

The TX300/e should be connected to a tributary port of network element or transmission system to ensure that the

switching time is measured for the service transported by the SDH network

Ensure that no errors or alarms are present on the transmission system because this will impact the measurement

The measurement will be triggered depending on the condition configured

The TX300/e measures how long the AIS event remains present after the event is first recognized and will continue

to measure the total disruption time in the event of multiple disruptions

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды