manualshive.com logo in svg

VeEX VePAL TX300, Руководство пользователя

Поделиться
Скачать
VeEX VePAL TX300 Скачать руководство пользователя страница 286

Go back to top

 

Go back to TOC

VLAN Tab:

 In the VLAN tab the following parameters are configured:

VLAN ID:

 Configurable in the range 1 to 4094.

VLAN ID is the identification of the VLAN, which is basically used by the standard 802.1Q.

It has 12 bits which allows the identification of 4096 (2^12) VLANs.

Of the 4096 possible VIDs, a VID of 0 is used to identify priority frames and value 4095 (FFF) is reserved.

Maximum possible VLAN configurations are therefore set to 4094.

VLAN Priority:

 Configurable in the range 0 to 6

Set by the Priority Code Point (PCP), a 3-bit field which refers to the IEEE 802.1p priority.

It indicates the frame priority level from 0 (lowest) to 7 (highest), which can be used to prioritize different

classes of traffic (voice, video, data, etc.).

Type:

 The following selections are possible:

8100 (IEEE 802.1Q tagged frame)

88a8 (IEEE 802.1ad Provider Bridging)

Drop Eligible:

 If enabled, drop eligibility flag will be set.

VLAN Flooding:

 Enable/Disable.

VLAN Flooding Range:

 Specifies the number of VLAN IDs. Enter a number from 0-4096. The VLAN IDs will be

incremented by 1 until it reaches the number of times entered in the flood range. 

IEEE 802.1Q VLAN Tag in an Ethernet Frame

BERT Setup - VLAN Tag configuration (Layer 3)

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды