VeEX VePAL TX300 Скачать руководство пользователя страница 15

Страница: 15 / 421

3.0 Safety Information

Safety precautions should be observed during all phases of operation of this instrument. The instrument has been designed to

ensure safe operation however please observe all safety markings and instructions. Do not operate the instrument in the

presence of flammable gases or fumes or any other combustible environment. VeEX Inc. assumes no liability for the customer's

failure to comply with safety precautions and requirements.

Optical Connectors

The TX300/e displays a laser warning icon when the laser source is active to alert the user about a potentially dangerous

situation. It is recommended to:

1. Deactivate the laser before connecting or disconnecting optical cables or patchcords.

2. Never look directly into an optical patchcord or an XFP's or SFP’s connector interface while the laser is enabled. Even

though XFP and SFP optical transceivers are typically fitted with Class 1 lasers, which are considered eye safe, optical

radiation for an extended period can cause irreparable damage to the eyes.

3. Never use a fiber microscope to check the optical connectors when the laser source is active.

Electrical Connectors

Telephone lines may carry dangerous voltages. Always connect the electrical test ports to known test interfaces which carry low

level signals.

Go back to TOC

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды