VeEX VePAL TX300 Скачать руководство пользователя страница 185

Страница: 185 / 421

Path Trace Byte (J0)

Regenerator section trace

Used to transmit a 16 or 64-byte identifier (trace) (including a CRC-7 byte) repeatedly so that all regenerators can verify

their connection

Used for continuity testing between regenerators

B1 Byte (RS-BIP)

An 8-bit even parity code used to check for transmission errors over the regenerator section.

Its value is calculated over all the bits of the STS-N frame before scrambling

The checksum value is placed in the SECTION overhead of the following STS-N before scrambling

B1 (Section-BIP) Byte

Order Wire Byte (E1)

Local order wire channel for voice communication between regenerators, cross connects, hubs and remote terminal

locations

F1 Byte

Section user channel

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды