manualshive.com logo in svg

VeEX VePAL TX300, Руководство пользователя

Поделиться
Скачать
VeEX VePAL TX300 Скачать руководство пользователя страница 74

Go back to top

 

Go back to TOC

6.7.3 General

The General setup page configures the audible alarm and APS protocol settings.

General tab

APS Protocol:

 Linear or Ring architectures are selectable. This determines how the APS bytes (K1/K2) are decoded in

the SDH Overhead Analyzer or how they are generated in the SDH Overhead Generator. It also determines how the APS

measurement will be made.

SDH/SONET: 

SDH or SONET modes are available options.

STS-1 Bulk data

 (SONET only): The STS-1 bulk mode fills the entire payload, except for the POH.

Result on start: 

On or Off. Provides an automatic move to Result screen when it starts.

Auto Save:

 Tap Auto Save and set it to 

ON

 to automatically save the results file.

Measurement Clock Source: 

Internal Clock or Tx Clock Source; the measurement is synchronized to the Transmitted

(Tx) Clock.

Tx Laser Override:

 (SONET/SDH MUX measurement) Enabling the Tx Laser Override causes whichever optical device

the Rx is using to produce a signal. The Tx data produced is random. The signal is of use to multiplexers that require an

input signal before they can transmit an optical signal. Tx Laser Override is only available when Rx is optical and Tx is in

PDH mode, (i.e. a Mux). 

Go back to top

 

Go back to TOC

6.7.4 Auto-Config

The Auto-Configuration function is described below.

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды