VeEX VePAL TX300 Скачать руководство пользователя страница 160

Страница: 160 / 421

Go back to top

Go back to TOC

J2 byte (LP)

Used to transmit a configurable 16-byte identifier that enables the receiving path to continuously verify its

connection with the transmitter

Uses the same byte structure as the J0 and J1 bytes

N2 byte (LP)

Provides LP/VT tandem connection monitoring function (LP-TCM) for the VC-11 and VC-12 levels

Bits 1-2: even parity error checking BIP-2 for the tandem connection

Bit 3: Set to “1”

Bit 4: Incoming AIS indicator (0 = no defect; 1 = defect occurred before tandem connection)

Bit 5: TC-REI indicating errored blocks caused in the tandem connection

Bit 6: OEI indicating errored blocks of the egressing VC-n

Bits 7-8: Operate in a 76 multi-frame structure:

Multiframe structure consists of:

Frames 1-8 >Frame Alignment Signal (FAS)

Frames 9-72 > The Access Point Identifier of the tandem connection (TC-API)

Frames 73-76 > TC-RDI indicating defects that have occurred in the tandem connection to the far-end

Frame 74 > ODI indicating to the far-end that AU/TU-AIS has been inserted into egressing AU-n/ TU-n due

to defects before or within the tandem connection

Frames 73-76 > Reserved capacity

K4 byte (LP path Extended Label)

When bits 5-7 of V5 byte are set to 101 (value = 5), then the signal label in K4 byte becomes valid where:

Bit 1 is allocated to the extended signal label

Bit 2 is allocated to virtual concatenation

Bits 3 and 4 are unassigned and are reserved for LP APS signaling

Bits 5, 6, 7 are allocated for optional use

Bit 8 is unassigned

Bits 12-19 contain the

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды