VeEX VePAL TX300 Скачать руководство пользователя страница 138

Страница: 138 / 421

Go back to top

Go back to TOC

Error Flow:

OTN, SDH, SONET, PDH signals

Injects different anomalies into the transmit signal. Error insertion flow modes include:

Single:

Inserts a single error every time the insertion button is tapped

Count:

Specific count or number of errors when the insertion button is tapped

Rate:

Specific rate between 1x10

-3

and 5x10

-6

The list of available error types depends on the type of framing being used and the SDH or PDH hierarchies and line interfaces

that have been selected.

Error Flow

Alarm Generation/Error Insertion

At any time during the test process, tap the

Error Injection

Alarm Generation

buttons to inject errors or generate alarms.

Go back to top

Go back to TOC

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

VeEX VePAL TX300, Руководство пользователя, Страница: 138 / 421

Результаты поиска

Содержание VePAL TX300

Отзывы: