VeEX VePAL TX300 Скачать руководство пользователя

Страница: 28 / 421

Copy Menu Options

Coupled:

TX and RX configurations are grouped as one block; TX and RX will have identical configuration. To uncouple

TX and RX settings, tap on the blue "Coupled" heading and select Independent from the Copy Menu.

Tx=Rx:

Tx blocks will copy the settings made in the Rx blocks

Rx=Tx:

Rx blocks will copy the settings made in the Tx blocks

Changes to the Setup are applied immediately unless an invalid parameter has been selected.

When the TX and RX signal structures need to be independent or asymmetrical, uncoupling the transmitter and receiver is

possible. For example, the TX could be sending a PRBS of 2^23-1 in a VC12 carried within an optical STM-64, while the RX

could be expecting to receive a PRBS of 2^23-1 in a 2Mbps E1 signal.

Hierarchy:

Allows the user to configure OTN/SDH, OTN/SONET, PDH signal and network types, including the bit rate and higher

order mapping, if applicable.

Interface:

Allows the user to select optical or electrical test ports. Optical test ports apply to OTN/SDH signal types only, while

electrical ports can apply to STTM-1E or PDH signals. Clock source and offset options are also configured in this screen.

Structure:

Applies to SDH/SONET signals only and allows the user to configure lower order mapping and the channel number.

Payload:

Applies to both SDH/SONET and PDH signals and allows the user to configure low rate signal (if applicable) and

associated framing.

Pattern:

Applies to both SDH/SONET and PDH signals and allows the user to configure the test pattern to be used. Use the

pattern drop-down box to select the test pattern which will be inserted into the transmitted signal. Pseudo Random Bit

Sequences (PRBS) defined by ITU-T 0.150 and 0.151 standards, fixed words and 24-bit or 32 bit user defined patterns are

available. Note, if the 32 bit user pattern entered is incorrect, the default pattern will be 0xFFFFFFFF.

Warning Message

While a test is running, it is possible to view the signal configuration, but it is not possible to change the setup or modify other

measurement settings. This warning screen is only shown during initial setup to alert the user.

Warning Message

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды