VeEX VePAL TX300 Скачать руководство пользователя страница 402

Страница: 402 / 421

16.3 RFC 2544

The RFC 2544 Ethernet test suite is adapted to Fiber Channel circuits to verify 1Gbps, 2Gbps, 4Gbps, 8Gbps and 10Gbps SAN

networks. The automated RFC 2544 test routine/analysis ensures repeatable installations:

Check buffer parameters needed to achieve desired Service Level Agreement (SLA)

Determine optimum buffer size - Capacity versus link speed

Determine minimum buffer credits for selected throughput for each frame length

Measuring throughput at various buffer credit sizes to check link quality

The test methodology is the same as for Ethernet testing. Please refer to the

RFC 2544

section for details.

Go back to top

Go back to TOC

16.4 Loopback

The Loopback function can be found on the Fiber Channel Home menu.

FC-1/2 Manual Loopback Setup

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды