VeEX VePAL TX300 Скачать руководство пользователя страница 24

Страница: 24 / 421

5.0 Home Menu and Switch Test Mode

The Home menu can be accessed at anytime during operation by pressing the

Home

key

on the rubber keypad. The

screen is divided into three presentation areas:

1 - Left:

LEDs:

Displays soft LEDs associated with Errors and Alarms.

Tools:

IP connection status, Advanced IP features (Net Wiz, WiFi Wiz, VoIP, and IPTV applications).

Utilities:

Applications (Help, Settings, Files) which are common to all VePAL handheld test sets.

Files:

Saved, USB, Manage.

2 - Middle:

Test Applications specific to the test set (Setup, Results, Alarm/Error, SDH/SONET Tools, PDH Tools, DS3/1 Tools,

OTN Tools, Profiles).

3 - Right:

Test Port:

Selects the test port.

Alarm/Err:

Shortcut menu that directs to the Alarm/Error page. Alternatively, this can be accessed by tapping on

the middle Alarm/Error icon.

Laser On/Off:

Enables/Disables the Laser transmitter on optical ports (SFP or XFP).

MX Discover:

Enables the test set to discover other test sets for loopback.

TX300/e Home Menu

Go back to top

Go back to TOC

Status icons:

The following icons are located at the top right hand corner of the screen.

Status Icons

Symbol

Status

Description

Laser On

Indicates if the optical transmitter in the SFP or XFP

transceiver is switched On or Off.

Laser Off

WiFi On

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды